why does my Honda CR-V have a humming noise when accelerating?

Honda CR-V Fifth Generation (2017-2022)

Error Codes

2-4 hours

Time

medium

Difficulty

medium

Severity

3 min read

591 words

Problem Statement

Learn how to diagnose and fix humming noise during acceleration in Honda CR-V. Step-by-step guide with diagnostic procedures and repair instructions.

Affected Component

Drivetrain

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on electrical systems.
•Allow the vehicle to cool before inspecting the drivetrain components.

Symptoms

•Humming noise that increases with acceleration
•Possible vibrations felt through the steering wheel or floor
•Noise may change pitch or intensity based on speed
•Diminished engine performance or responsiveness
•Potential rattling or grinding sounds accompanying the hum

Diagnostic Steps

1
Inspect the tires for uneven wear or damage that could cause noise while driving.
2
Check wheel bearings for play or roughness by spinning the wheel and listening for noise.
3
Examine the drivetrain components, including the driveshaft and CV joints, for wear or damage.
4
Scan the vehicle's onboard computer with an OBD-II scanner for any error codes related to the engine or transmission.
5
Test the transmission fluid level and condition, looking for signs of contamination or low levels.
6
Listen for the noise while in neutral to determine if it's engine-related or drivetrain-related.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Jack and jack stands
•Tire pressure gauge
•Bearing puller (if replacing bearings)
•Socket set

Parts Required

•Wheel bearings (if needed)
•CV joint boots (if torn)
•Transmission fluid (if topping off or changing)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Inspect the tires for uneven wear or damage that could cause noise while driving.
2
Check wheel bearings for play or roughness by spinning the wheel and listening for noise.
3
Examine the drivetrain components, including the driveshaft and CV joints, for wear or damage.
4
Scan the vehicle's onboard computer with an OBD-II scanner for any error codes related to the engine or transmission.
5
Test the transmission fluid level and condition, looking for signs of contamination or low levels.
6
Listen for the noise while in neutral to determine if it's engine-related or drivetrain-related.

Solution

1. Preparation

Gather tools and parts needed for the repair.
Ensure the vehicle is parked on a level surface and secure it with wheel chocks.
Disconnect the battery to ensure safety during inspection.

2. Tire and Wheel Inspection

Sub-steps:
- Remove hubcaps or wheel covers if necessary.
- Inspect each tire for uneven wear, bulges, or foreign objects.
- Check tire pressure and inflate to the manufacturer's specifications.
- Rotate tires if needed to balance wear.
- Reinstall hubcaps or wheel covers.

3. Wheel Bearing Inspection

Sub-steps:
- Jack up the vehicle and secure it on jack stands.
- Spin each wheel by hand and listen for any grinding or roughness.
- If noise is present, remove the wheel and inspect the bearings for wear.
- Replace bearings if necessary, using a bearing puller and appropriate tools.

4. Drivetrain Component Examination

Sub-steps:
- Inspect the driveshaft for any signs of damage or excessive play.
- Check CV joints for grease leaks or torn boots.
- Replace any damaged components with new parts, ensuring proper alignment and torque specifications.

5. Transmission Fluid Inspection

Sub-steps:
- Locate the transmission dipstick (if equipped) and check the fluid level.
- If fluid is low, top it off with the manufacturer-recommended transmission fluid.
- If fluid appears burnt or contaminated, consider a transmission fluid change.