why does my Honda CR-V feel like it’s slipping when I change gears?

Honda CR-V Fifth Generation (2017-2022)

Error Codes

2-4 hours

Time

medium

Difficulty

high

Severity

3 min read

513 words

⚠️ Safety Warning

This issue requires immediate attention. If you are not experienced with automotive repairs, consult a professional mechanic. Working on critical systems can be dangerous.

Problem Statement

Learn how to diagnose and fix transmission slipping issues in Honda CR-V. Step-by-step guide with symptoms, diagnostic steps, and repair instructions.

Affected Component

Transmission

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on electrical systems.
•Use gloves and safety goggles when handling transmission fluid to prevent skin and eye irritation.

Symptoms

•Engine revs without corresponding acceleration
•Harsh or delayed gear shifts
•Unusual noises during gear changes (e.g., grinding or whining)
•Warning lights on the dashboard (e.g., transmission or check engine light)
•Fluid leaks under the vehicle (transmission fluid)

Diagnostic Steps

1
Scan for error codes using an OBD-II scanner to identify any transmission-related codes.
2
Check the transmission fluid level and condition; look for burnt smell or discoloration.
3
Inspect the transmission fluid for leaks at the transmission pan and seals.
4
Test the transmission solenoids for proper operation with a multimeter.
5
Examine the throttle position sensor (TPS) for proper operation and alignment.
6
Inspect the engine and transmission mounts for wear or damage.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Socket set
•Multimeter
•Transmission fluid pump
•Torque wrench

Parts Required

•Transmission fluid
•Transmission filter
•Gasket for transmission pan
•Transmission solenoids (if faulty)
•Throttle position sensor (if faulty)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Scan for error codes using an OBD-II scanner to identify any transmission-related codes.
2
Check the transmission fluid level and condition; look for burnt smell or discoloration.
3
Inspect the transmission fluid for leaks at the transmission pan and seals.
4
Test the transmission solenoids for proper operation with a multimeter.
5
Examine the throttle position sensor (TPS) for proper operation and alignment.
6
Inspect the engine and transmission mounts for wear or damage.

Solution

1. Preparation

Gather tools and parts required for the repair.
Ensure the vehicle is parked on a level surface and engage the parking brake.
Disconnect the battery to avoid any electrical short circuits.

2. Check and Replace Transmission Fluid

Sub-steps:
1. Locate the transmission dipstick and remove it to check fluid level.
2. If fluid is low, add the appropriate type (refer to the owner's manual for specific fluid type).
3. If fluid is discolored or burnt, drain the old fluid by removing the transmission pan.
4. Replace the transmission filter and gasket.
5. Reinstall the pan and fill with new transmission fluid to the correct level.

3. Inspect and Replace Transmission Solenoids

Sub-steps:
1. Remove the transmission access cover to reach the solenoids.
2. Disconnect the electrical connectors from the solenoids.
3. Remove the solenoids using a socket set.
4. Install new solenoids, ensuring they are securely fastened.
5. Reconnect the electrical connectors and cover.

4. Check and Adjust Throttle Position Sensor (TPS)

Sub-steps:
1. Locate the TPS on the throttle body.
2. Disconnect the electrical connector from the TPS.
3. Using a multimeter, measure the resistance across the terminals to ensure it operates within specifications.
4. If out of range, replace the TPS and reconnect the connector.

Tools Required:

OBD-II scanner
Socket set
Multimeter
Transmission fluid pump
Torque wrench

Parts Required:

Transmission fluid
Transmission filter
Gasket for transmission pan
Transmission solenoids (if faulty)
Throttle position sensor (if faulty)

Estimated Repair Time: 2-4 hours

Safety Warnings:

Disconnect the battery before working on electrical systems.
Use gloves and safety goggles when handling transmission fluid to prevent skin and eye irritation.