my Honda CR-V makes a knocking noise when accelerating what's causing it

Honda CR-V Fifth Generation (2017-2022)

Error Codes

2-4 hours

Time

medium

Difficulty

medium

Severity

3 min read

573 words

Problem Statement

Diagnose and fix knocking noise during acceleration in Honda CR-V. Step-by-step guide with symptoms, diagnostic steps, tools, and repair instructions.

Affected Component

Engine

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Allow the engine to cool before opening the hood.
•Ensure the vehicle is securely supported on jack stands if needed.
•Disconnect the battery before working on electrical systems.

Symptoms

•Knocking noise when accelerating
•Potential loss of power
•Engine vibration felt through the vehicle
•Check engine light may be illuminated
•Unusual engine sounds during idle

Diagnostic Steps

1
Scan for error codes using an OBD-II scanner to identify any stored fault codes.
2
Inspect the engine oil level and condition; low or dirty oil can cause knocking.
3
Check for loose or damaged engine mounts that may cause vibrations.
4
Inspect the exhaust system for any loose components that could create noise.
5
Examine the drive belts and pulleys for wear or damage.
6
Perform a visual inspection of the suspension components for any signs of damage.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Socket set
•Pry bar
•Wrench set
•Belt tension gauge
•Oil funnel

Parts Required

•Engine oil (as needed)
•Engine mounts (if damaged)
•Drive belts (if worn)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Scan for error codes using an OBD-II scanner to identify any stored fault codes.
2
Inspect the engine oil level and condition; low or dirty oil can cause knocking.
3
Check for loose or damaged engine mounts that may cause vibrations.
4
Inspect the exhaust system for any loose components that could create noise.
5
Examine the drive belts and pulleys for wear or damage.
6
Perform a visual inspection of the suspension components for any signs of damage.

Solution

1. Preparation

Ensure the vehicle is parked on a level surface and the engine is cool.
Gather tools and parts for the repair.

2. Engine Oil Check

Sub-steps:
1. Open the hood and locate the dipstick.
2. Remove the dipstick, wipe it clean, and reinsert it to check the oil level.
3. If the oil level is low, add the recommended oil type (consult the owner's manual for specifications).
Tools Required: Oil funnel, appropriate engine oil.
Safety Warnings: Allow the engine to cool before opening the hood.

3. Inspect Engine Mounts

Sub-steps:
1. Visually inspect the engine mounts for cracks or separation.
2. Use a pry bar to check for excessive movement in the mounts.
3. If damaged, remove the bolts securing the mount and replace with a new one.
Tools Required: Socket set, pry bar.
Safety Warnings: Ensure the vehicle is securely supported on jack stands if needed.

4. Check Exhaust System

Sub-steps:
1. Start the engine and listen for the knocking noise while inspecting the exhaust system.
2. Look for loose hangers, damaged pipes, or leaks.
3. Tighten or replace any loose or damaged components as necessary.
Tools Required: Wrench set, exhaust clamp tool.

5. Inspect Drive Belts and Pulleys

Sub-steps:
1. Visually inspect the drive belts for cracks or wear.
2. Check the tension of the belts; adjust if necessary.
3. Replace any worn belts and ensure pulleys are aligned properly.
Tools Required: Socket set, belt tension gauge.

6. Suspension Inspection

Sub-steps:
1. Check for any loose or damaged suspension components.
2. Inspect for worn bushings or ball joints.
3. Replace any damaged parts to eliminate noise.
Tools Required: Socket set, suspension tool kit.