my Honda CR-V is making a clicking noise when I accelerate what's wrong

Honda CR-V Fifth Generation (2017-2022)

Error Codes

2-4 hours

Time

medium

Difficulty

medium

Severity

3 min read

474 words

Problem Statement

Learn how to diagnose and fix clicking noise during acceleration in Honda CR-V. Step-by-step guide with diagnostic procedures and repair instructions.

Affected Component

Drivetrain

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on electrical systems.
•Allow the engine to cool before inspecting the exhaust system.

Symptoms

•Clicking noise when accelerating
•Potential vibration felt through the steering wheel
•Loss of power during acceleration
•Unusual engine performance
•Possible check engine light illuminated

Diagnostic Steps

1
Inspect the CV joints and axles for damage or wear.
2
Check for loose or damaged heat shields.
3
Perform a visual inspection of the engine mounts.
4
Scan for error codes using an OBD-II scanner.
5
Test drive the vehicle to replicate the noise and note conditions (speed, turning, etc.).
6
Inspect the exhaust system for loose components or leaks.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Socket set
•Torque wrench
•OBD-II scanner
•Jack stands
•Safety glasses

Parts Required

•CV joint or axle (if damaged)
•Heat shield (if damaged)
•Engine mount (if damaged)
•Exhaust hangers or sections (if damaged)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Inspect the CV joints and axles for damage or wear.
2
Check for loose or damaged heat shields.
3
Perform a visual inspection of the engine mounts.
4
Scan for error codes using an OBD-II scanner.
5
Test drive the vehicle to replicate the noise and note conditions (speed, turning, etc.).
6
Inspect the exhaust system for loose components or leaks.

Solution

1. Preparation

Gather tools: jack stands, socket set, torque wrench, OBD-II scanner, and safety glasses.
Ensure the vehicle is on a flat surface and securely lifted.

2. Inspect CV Joints and Axles

1.1 Remove the front wheels using a socket set.
1.2 Inspect the CV boots for tears or damage.
1.3 Check the CV joints for play or excessive wear. If damaged, replace the CV joint or axle.
1.4 Reinstall the wheel and torque lug nuts to manufacturer specifications.

3. Check Heat Shields

2.1 Visually inspect the heat shields around the exhaust system.
2.2 Tighten any loose bolts or screws that secure the heat shields.
2.3 Replace any damaged heat shields as necessary.

4. Examine Engine Mounts

3.1 Inspect engine mounts for cracks or wear.
3.2 If damaged, remove the affected mount using a socket set and replace it with a new one.
3.3 Torque the new mount to manufacturer specifications.

5. Exhaust System Inspection

4.1 Check the exhaust system for loose connections or broken hangers.
4.2 Tighten any loose bolts or replace broken hangers.
4.3 If leaks are found, replace the affected sections of the exhaust.