how to diagnose wheel bearing noise in Honda CR-V Fifth Generation (2017-2022)

Honda CR-V Fifth Generation (2017-2022)

Error Codes

2-4 hours

Time

medium

Difficulty

medium

Severity

3 min read

551 words

Problem Statement

Learn how to diagnose and fix wheel bearing noise in Honda CR-V Fifth Generation (2017-2022). Step-by-step guide with symptoms and diagnostic procedures.

Affected Component

Suspension

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Always use jack stands when working under a vehicle.
•Allow the vehicle to cool before handling brake components.

Symptoms

•Humming or grinding noise that increases with vehicle speed
•Noise that changes when turning left or right
•Vibration felt through the steering wheel or floor
•Uneven tire wear
•Clunking sound when going over bumps

Diagnostic Steps

1
Perform a visual inspection of the tires and wheel wells for any signs of damage or uneven wear.
2
Lift the vehicle using a jack and secure it with jack stands to safely access the wheel assemblies.
3
Spin each wheel by hand to listen for any unusual noises or resistance.
4
Check for play in the wheel bearings by gripping the top and bottom of the tire and rocking it back and forth.
5
Use an OBD-II scanner to check for any related trouble codes that may indicate suspension or drivetrain issues.
6
Drive the vehicle at various speeds and listen for changes in noise when turning or applying brakes.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Jack
•Jack stands
•Lug wrench
•Wheel chocks
•Safety goggles
•Socket set
•Torque wrench
•Bearing puller

Parts Required

•New wheel bearing kit

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Perform a visual inspection of the tires and wheel wells for any signs of damage or uneven wear.
2
Lift the vehicle using a jack and secure it with jack stands to safely access the wheel assemblies.
3
Spin each wheel by hand to listen for any unusual noises or resistance.
4
Check for play in the wheel bearings by gripping the top and bottom of the tire and rocking it back and forth.
5
Use an OBD-II scanner to check for any related trouble codes that may indicate suspension or drivetrain issues.
6
Drive the vehicle at various speeds and listen for changes in noise when turning or applying brakes.

Solution

1. Preparation

Tools Required: Jack, jack stands, lug wrench, wheel chocks, and safety goggles.
Ensure the vehicle is parked on a flat surface and the ignition is off.
Apply the parking brake and chock the rear wheels.

2. Lift the Vehicle

Use the jack to lift the front or rear of the vehicle depending on the suspected wheel bearing.
Place jack stands under the vehicle for added safety.

3. Remove the Wheel

Using a lug wrench, loosen and remove the lug nuts on the wheel being serviced.
Carefully remove the wheel and set it aside.

4. Inspect and Replace the Wheel Bearing

Tools Required: Socket set, torque wrench, bearing puller, grease, and new wheel bearing kit.
Inspect the wheel bearing visually for rust, play, or damage.
If replacement is necessary:
1. Remove the caliper and rotor to access the wheel bearing assembly.
2. Use a bearing puller to remove the old bearing from the hub.
3. Clean the hub area and apply new grease.
4. Install the new wheel bearing, ensuring it is seated properly.
5. Reinstall the rotor and caliper, torqueing the bolts to the manufacturer's specifications.

5. Reinstall the Wheel

Place the wheel back onto the hub.
Hand-tighten the lug nuts before lowering the vehicle.
Once the vehicle is on the ground, use the torque wrench to torque the lug nuts to the specified value.