why is my Honda Civic 9th Generation (2012-2015) making a grinding noise when turning

Honda Civic 9th Generation (2012-2015)

Error Codes

2-4 hours

Time

medium

Difficulty

medium

Severity

3 min read

554 words

Problem Statement

Learn how to diagnose and fix grinding noise when turning in Honda Civic 9th Generation. Step-by-step guide with symptoms, diagnostics, and repair instructions.

Affected Component

Steering

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on electrical systems.
•Always use jack stands when working under a vehicle.

Symptoms

•Grinding noise when turning the steering wheel
•Vibration in the steering wheel during turns
•Difficulty in steering or a loose steering feel
•Uneven tire wear
•Possible fluid leaks under the vehicle

Diagnostic Steps

1
Inspect the power steering fluid level and condition.
2
Check for any visible leaks in the power steering system.
3
Examine the condition of the CV joints and boots for damage or wear.
4
Inspect the wheel bearings for play or roughness.
5
Evaluate the suspension components, including struts and bushings, for wear.
6
Test drive the vehicle to replicate the grinding noise while turning.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Jack
•Jack stands
•Socket set
•Torque wrench
•Bearing puller
•Funnel
•Grease

Parts Required

•Power steering fluid
•CV joint replacement kit
•Wheel bearings (if needed)
•Suspension components (if worn)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Inspect the power steering fluid level and condition.
2
Check for any visible leaks in the power steering system.
3
Examine the condition of the CV joints and boots for damage or wear.
4
Inspect the wheel bearings for play or roughness.
5
Evaluate the suspension components, including struts and bushings, for wear.
6
Test drive the vehicle to replicate the grinding noise while turning.

Solution

1. Preparation

Gather necessary tools and parts.
Park the vehicle on a level surface and engage the parking brake.
Disconnect the battery to ensure safety while working on electrical components.

2. Check and Refill Power Steering Fluid

Tools Required: Funnel, power steering fluid
Inspect the power steering fluid reservoir for the correct level.
If low, add the recommended power steering fluid until it reaches the proper level.

3. Inspect and Replace CV Joints

Tools Required: Jack, jack stands, socket set, grease, CV joint replacement kit
Lift the vehicle using a jack and secure it with jack stands.
Remove the wheel to gain access to the CV joint.
Inspect the CV joint for torn boots or excessive play.
If damaged, remove the old CV joint by disconnecting it from the transmission side and the wheel hub.
Install the new CV joint, ensuring it’s properly greased and secured.

4. Replace Wheel Bearings (if necessary)

Tools Required: Bearing puller, socket set, torque wrench
Remove the wheel and brake components to access the hub assembly.
Use a bearing puller to extract the old wheel bearing from the hub.
Install the new wheel bearing, ensuring it is pressed in evenly.
Reassemble the hub, brakes, and wheel, and torque all components to manufacturer specifications.

5. Inspect and Replace Suspension Components (if needed)

Tools Required: Socket set, pry bar, torque wrench
Inspect struts, control arms, and bushings for wear.
Replace any worn components using appropriate tools and torque settings specified in the vehicle’s service manual.