why does my Honda Civic 9th Generation (2012-2015) make a clicking sound when I accelerate?

Honda Civic 9th Generation (2012-2015)

Error Codes

2-4 hours

Time

medium

Difficulty

medium

Severity

3 min read

591 words

Problem Statement

Learn how to diagnose and fix the clicking sound during acceleration in Honda Civic 9th Generation. Step-by-step guide with symptoms and solutions.

Affected Component

Drivetrain

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on electrical systems.
•Allow the engine to cool before starting the inspection and repair process.

Symptoms

•Clicking noise that increases with acceleration
•Vibration felt through the steering wheel
•Poor acceleration performance
•Possible loss of power during acceleration
•Unusual noises when turning

Diagnostic Steps

1
Inspect the CV joints for damage or wear.
2
Check the condition of the engine mounts.
3
Examine the transmission fluid level and condition.
4
Test drive the vehicle to replicate the clicking sound while observing related symptoms.
5
Inspect the wheel bearings for wear or damage.
6
Evaluate the drive shaft for any signs of damage or misalignment.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Socket set
•Jack and jack stands
•Bearing puller
•Torque wrench

Parts Required

•CV joint or axle assembly
•Engine mounts (if needed)
•Transmission fluid (if changing)
•Wheel bearings (if needed)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Inspect the CV joints for damage or wear.
2
Check the condition of the engine mounts.
3
Examine the transmission fluid level and condition.
4
Test drive the vehicle to replicate the clicking sound while observing related symptoms.
5
Inspect the wheel bearings for wear or damage.
6
Evaluate the drive shaft for any signs of damage or misalignment.

Solution

1. Preparation

Gather tools and parts needed for the repair.
Park the vehicle on a flat surface and engage the parking brake.
Disconnect the battery to ensure safety while working on electrical components.

2. Inspect and Replace CV Joints

Inspect CV Joints:
- Raise the front of the vehicle using a jack and secure it with jack stands.
- Remove the front wheels using a socket set.
- Visually inspect the CV joints for torn boots or grease leakage.
Replace CV Joints (if necessary):
- Remove the axle nut with a socket and breaker bar.
- Disconnect the lower control arm to free the CV joint from the hub assembly.
- Remove the old CV joint and install the new one, ensuring proper alignment.
- Reassemble the components and torque the axle nut to the manufacturer’s specifications (typically around 130 ft-lbs).

3. Check and Replace Engine Mounts (if needed)

Inspect Engine Mounts:
- Visually inspect engine mounts for cracks or separation.
Replace Engine Mounts (if necessary):
- Support the engine with a jack and a piece of wood to distribute the weight.
- Remove the bolts securing the engine mount to the engine block.
- Remove and replace the mount, then torque the bolts to the manufacturer's specifications.

4. Inspect and Change Transmission Fluid

Check Fluid Level:
- Locate the transmission dipstick and check the fluid level.
Change Fluid (if needed):
- Drain the transmission fluid using a drain pan.
- Replace the transmission fluid filter if applicable.
- Refill with the recommended transmission fluid type (usually Honda ATF-Z1 or DW-1).

5. Inspect Wheel Bearings

Check Wheel Bearings:
- Spin the wheel and listen for any grinding or roughness.
Replace Wheel Bearings (if necessary):
- Remove the wheel and brake components.
- Use a bearing puller to remove the old wheel bearing and replace it with a new one.
- Reassemble and torque all fasteners to specifications.