why does my Honda Civic 9th Generation (2012-2015) make a clicking noise when I turn the steering wh...

Honda Civic 9th Generation (2012-2015)

Error Codes

2-4 hours

Time

medium

Difficulty

medium

Severity

3 min read

564 words

Problem Statement

Learn how to diagnose and fix clicking noise when turning the steering wheel in Honda Civic 9th Generation. Step-by-step guide with diagnostic procedures and repair instructions.

Affected Component

Steering

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Ensure the vehicle is securely lifted and on jack stands before working underneath.
•Always wear safety goggles when using power tools.

Symptoms

•Clicking or popping noise when turning the steering wheel
•Noise occurs during both left and right turns
•Increased steering effort in certain positions
•Vibration felt through the steering wheel
•Possible looseness in the steering column

Diagnostic Steps

1
Inspect the steering column for any visible wear or damage.
2
Check the CV joints for signs of grease leakage or damage.
3
Examine the outer tie rods and inner tie rods for wear or play.
4
Inspect the power steering fluid level and condition.
5
Test the steering rack for any signs of failure or abnormal movement.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Jack
•Jack stands
•Socket set
•Torque wrench
•Tie rod end puller
•Pry bar

Parts Required

•CV joint assembly (if damaged)
•Outer tie rod (if worn)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Inspect the steering column for any visible wear or damage.
2
Check the CV joints for signs of grease leakage or damage.
3
Examine the outer tie rods and inner tie rods for wear or play.
4
Inspect the power steering fluid level and condition.
5
Test the steering rack for any signs of failure or abnormal movement.

Solution

1. Preparation

Gather tools and parts before starting the repair.
Ensure the vehicle is parked on a flat surface and the engine is off.
Gather necessary tools: jack, jack stands, socket set, torque wrench, and pry bar.

2. Inspect and Replace CV Joints (if damaged)

Sub-steps:
1. Lift the vehicle using a jack and secure with jack stands.
2. Remove the front wheels using a socket set.
3. Inspect the CV joints for cracks or torn boots.
4. If damaged, remove the axle nut using a socket and impact wrench.
5. Disconnect the lower control arm to free the CV joint from the hub.
6. Remove the CV joint from the transaxle; replace with a new joint.
7. Reassemble in reverse order, ensuring all fasteners are torqued to manufacturer specifications.

3. Check and Replace Tie Rods (if needed)

Sub-steps:
1. After lifting the vehicle, visually inspect the tie rods for any damage or play.
2. If worn, mark the position of the outer tie rod on the inner tie rod.
3. Remove the outer tie rod end from the steering knuckle using a tie rod end puller.
4. Unscrew the outer tie rod from the inner tie rod to replace it.
5. Install the new outer tie rod, adjusting to the marked position.
6. Reattach the tie rod end to the steering knuckle and torque to specifications.

4. Inspect Power Steering Components

Sub-steps:
1. Check the power steering fluid level; fill it if low.
2. Inspect power steering hoses for leaks or damage.
3. If the fluid is contaminated, consider flushing the power steering system.
4. Replace any damaged hoses or components.