what causes my Honda Civic 9th Generation (2012-2015) to shake when I'm driving?

Honda Civic 9th Generation (2012-2015)

Error Codes

2-4 hours

Time

medium

Difficulty

medium

Severity

3 min read

529 words

Problem Statement

Discover the causes of shaking in your Honda Civic 9th Generation. Follow our diagnostic steps and solutions to resolve the issue effectively.

Affected Component

Suspension

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Always use jack stands when working under a vehicle.
•Allow the vehicle to cool before inspecting brakes to avoid burns.

Symptoms

•Vibration felt in the steering wheel
•Shaking in the seats or floor of the vehicle
•Increased noise during operation
•Shaking at specific speeds (e.g., 40-60 mph)
•Steering wheel may shake or pull to one side
•Possible check engine light illumination

Diagnostic Steps

1
Inspect tire condition and pressure for uneven wear or low inflation.
2
Check wheel balance and alignment by performing a visual inspection and using alignment tools.
3
Examine suspension components for wear, including struts, shocks, and bushings.
4
Scan for any diagnostic trouble codes (DTC) using an OBD-II scanner.
5
Check for issues with the drivetrain, including the driveshaft and CV joints.
6
Inspect brake components for warpage, particularly the brake rotors.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Jack
•Jack stands
•Wheel chocks
•Tire pressure gauge
•Torque wrench
•OBD-II scanner
•Basic hand tools

Parts Required

•Tires (if damaged)
•Suspension components (if worn)
•Brake rotors (if warped)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Inspect tire condition and pressure for uneven wear or low inflation.
2
Check wheel balance and alignment by performing a visual inspection and using alignment tools.
3
Examine suspension components for wear, including struts, shocks, and bushings.
4
Scan for any diagnostic trouble codes (DTC) using an OBD-II scanner.
5
Check for issues with the drivetrain, including the driveshaft and CV joints.
6
Inspect brake components for warpage, particularly the brake rotors.

Solution

1. Preparation

Gather tools: jack, jack stands, wheel chocks, tire pressure gauge, torque wrench, OBD-II scanner, and basic hand tools.
Ensure the vehicle is on a flat surface and set the parking brake.

2. Tire Inspection

Check Tire Pressure
- Use a tire pressure gauge to measure each tire's pressure.
- Inflate tires to the manufacturer's recommended PSI if low.
Inspect for Damage
- Look for bulges, cuts, or uneven wear on the tire surface.
- Replace any damaged tires with new ones.

3. Wheel Balancing and Alignment

Balance Wheels
- Remove each wheel and take it to a tire shop for balancing.
- Reinstall wheels after balancing.
Check Alignment
- If misalignment is suspected, perform a wheel alignment following the manufacturer’s specifications.

4. Suspension Inspection

Inspect Components
- Visually check the struts, shocks, and bushings for wear or damage.
- Replace any worn or damaged components as necessary.

5. Drivetrain Check

Examine Driveshaft and CV Joints
- Inspect the driveshaft for any signs of damage or excessive play.
- Check CV joints for torn boots or grease leakage. Replace if necessary.

6. Brake Inspection

Inspect Brake Rotors
- Remove the wheel to access the brake rotor.
- Use a micrometer to measure rotor thickness; replace if below minimum thickness.
- If the rotors are warped, resurface or replace them as required.