FAULTBASE
Error CodesASKCars
© 2026 FAULTBASE
All rights reserved.
v2.0.0 • Production
ContactPrivacyImpressum
my Honda Civic 9th Generation (2012-2015) has low oil pressure what should I check - Honda Civic
Home/Cars/Honda/Civic/9th Generation (2012-2015)/my Honda Civic 9th Generation (2012-2015) has low oil pressure what should I check

my Honda Civic 9th Generation (2012-2015) has low oil pressure what should I check

Honda Civic 9th Generation (2012-2015)

Error Codes
2-4 hours
Time
medium
Difficulty
high
Severity
Navigation
ProblemSymptomsDiagnosisSolution
ProblemSymptomsDiagnosisSolution
3 min read
541 words

⚠️ Safety Warning

This issue requires immediate attention. If you are not experienced with automotive repairs, consult a professional mechanic. Working on critical systems can be dangerous.

Problem Statement

Learn how to diagnose and fix low oil pressure in Honda Civic 9th Generation (2012-2015). Step-by-step guide with symptoms, diagnostic steps, and repair instructions.

Affected Component
Engine
Estimated Time
2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

  • •Disconnect battery before working on electrical components.
  • •Allow engine to cool before draining oil to prevent burns.

Symptoms

  • •Oil pressure warning light illuminated on the dashboard
  • •Engine noise (ticking or knocking sounds)
  • •Decreased engine performance
  • •Oil leaks under the vehicle
  • •Poor acceleration or stalling

Diagnostic Steps

  1. 1
  2. 2
  3. 3
  4. 4
  5. 5
  6. 6

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

  • ✓Test the affected component to ensure it functions correctly
  • ✓Check for any error codes or warning lights
  • ✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

  • •Follow the manufacturer's recommended maintenance schedule
  • •Address warning signs early before they develop into major issues
  • •Use quality parts and fluids recommended for your vehicle
  • •Keep detailed records of all repairs and maintenance

Tools & Equipment Required

  • •OBD-II scanner
  • •Oil filter wrench
  • •Socket set
  • •Torque wrench
  • •Drain pan
  • •External oil pressure gauge

Parts Required

  • •Engine oil (0W-20 or 5W-20)
  • •Oil filter
  • •Oil pressure sending unit (if faulty)

Additional Information

Affected Component
Engine
Estimated Time
2-4 hours
Difficulty
medium
Severity
high
Tools Required
6 items
Parts Required
3 items

Related Faults

Loading...

Share this solution

Comments

Sign in to share your thoughts

Sign In

No comments yet

Be the first to share your thoughts

Back to Generation
Solution
1. Preparation
  • Gather tools and parts for the repair.
  • Ensure the vehicle is parked on a level surface and the engine is cool.
  • Disconnect the battery to avoid any electrical issues.
2. Oil Change

  1. Drain Old Oil:

    • Place a drain pan under the oil pan.
    • Remove the oil drain plug using a socket set and allow oil to drain completely.
    • Replace the drain plug and torque to manufacturer specifications (typically around 20-30 ft-lbs).

  2. Replace Oil Filter:

    • Locate the oil filter and remove it using an oil filter wrench.
    • Apply a thin layer of fresh oil to the rubber gasket of the new oil filter.
    • Install the new oil filter by hand until snug, then give it an additional three-quarters turn.

  3. Add New Oil:

    • Remove the oil filler cap and pour in the recommended type and amount of new oil (typically 0W-20 or 5W-20, around 4.5 quarts).
    • Replace the oil filler cap.
3. Inspect and Replace Oil Pressure Sending Unit

  1. Locate the Oil Pressure Sending Unit:

    • Identify the sending unit, usually located near the oil filter or on the engine block.

  2. Remove and Replace:

    • Disconnect the electrical connector from the sending unit.
    • Use a socket or wrench to remove the sending unit.
    • Install the new sending unit and torque to manufacturer specifications.
    • Reconnect the electrical connector.