why does my Honda Civic 10th Generation (2016-2021) make a noise when I accelerate?

Honda Civic 11th Generation (2022-Present)

Error Codes

2-4 hours

Time

medium

Difficulty

medium

Severity

4 min read

636 words

Problem Statement

Learn how to diagnose and fix noise during acceleration in Honda Civic 10th Generation (2016-2021). Step-by-step guide with diagnostic procedures and repair instructions.

Affected Component

Exhaust System

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Always engage the parking brake and disconnect the battery before working on electrical systems
•Allow the engine to cool before working on any components under the hood

Symptoms

•Noise that increases with acceleration
•Possible vibration felt in the cabin
•Reduced engine performance or responsiveness
•Loud exhaust noise
•Check engine light illuminated (if applicable)

Diagnostic Steps

1
Scan for error codes using OBD-II scanner
2
Inspect the exhaust system for leaks, loose connections, or damaged components
3
Check engine mounts for wear or damage
4
Examine the drive belt for signs of wear or damage
5
Conduct a test drive to replicate the noise and determine under what conditions it occurs
6
Check the transmission fluid level and condition

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Jack and jack stands
•Socket set
•Torque wrench
•Flashlight

Parts Required

•Exhaust gaskets or sections (if needed)
•Engine mounts (if worn)
•Drive belt (if worn)
•Transmission fluid (if low or contaminated)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Scan for error codes using OBD-II scanner
2
Inspect the exhaust system for leaks, loose connections, or damaged components
3
Check engine mounts for wear or damage
4
Examine the drive belt for signs of wear or damage
5
Conduct a test drive to replicate the noise and determine under what conditions it occurs
6
Check the transmission fluid level and condition

Solution

1. Preparation

Tools Needed: OBD-II scanner, jack and jack stands, socket set, torque wrench, and a flashlight.
Safety Warnings: Always engage the parking brake and disconnect the battery before working on electrical systems.

2. Address Exhaust System Issues

Inspect for Leaks:
- With the engine running, listen for hissing or popping sounds near the exhaust.
- Use a flashlight to check the exhaust pipes, connections, and muffler for any visible damage.
Repair or Replace:
- If leaks are found, replace gaskets or sections of the exhaust as necessary.
- Tighten any loose bolts or clamps.

3. Replace Worn Engine Mounts

Remove Old Mounts:
- Use a socket set to remove the bolts securing the affected engine mounts.
- Lift the engine slightly using a jack to relieve tension on the mounts.
Install New Mounts:
- Position new engine mounts in place and hand-tighten the bolts.
- Lower the engine and torque bolts to the manufacturer’s specifications (consult service manual for exact torque values).

4. Replace Drive Belt

Remove the Old Belt:
- Use a socket or wrench to relieve tension on the serpentine belt tensioner.
- Slide the old belt off the pulleys.
Install New Belt:
- Refer to the belt routing diagram (typically found on a sticker under the hood).
- Ensure the belt is properly seated on all pulleys and reapply tension.

5. Transmission Fluid Maintenance

Check Fluid Level:
- With the engine running, check the transmission fluid level using the dipstick.
Change Fluid if Necessary:
- If the fluid is low or discolored, drain the old fluid and replace it with new fluid as specified in the owner’s manual.