why does my Honda Civic 10th Generation (2016-2021) make a grinding noise when turning

Honda Civic 11th Generation (2022-Present)

Error Codes

2-4 hours

Time

medium

Difficulty

high

Severity

3 min read

531 words

⚠️ Safety Warning

This issue requires immediate attention. If you are not experienced with automotive repairs, consult a professional mechanic. Working on critical systems can be dangerous.

Problem Statement

Discover how to diagnose and fix grinding noise when turning in Honda Civic 10th Generation (2016-2021). Step-by-step guide with tools and parts needed.

Affected Component

Steering

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Ensure the vehicle is on a flat surface and secured with wheel chocks before lifting.
•Always disconnect the battery before working on electrical components.
•Allow the vehicle to cool before working on the brakes or suspension.

Symptoms

•Grinding noise during turns
•Vibration felt through the steering wheel
•Difficulty steering or increased steering effort
•Unusual wear on tires
•Steering wheel misalignment

Diagnostic Steps

1
Inspect the power steering fluid level and condition.
2
Check for any visible damage or wear on the CV joints and boots.
3
Examine the wheel bearings for play or damage.
4
Test drive the vehicle to replicate the noise and note the conditions (e.g., sharp turns, speed).
5
Inspect suspension components such as struts and bushings for wear or damage.
6
Check tire condition and alignment for uneven wear or pressure issues.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Jack and jack stands
•Wheel chocks
•Socket set
•Torque wrench
•Bearing press or hammer

Parts Required

•New CV axle (if damaged)
•New wheel bearing (if needed)
•New struts (if required)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Inspect the power steering fluid level and condition.
2
Check for any visible damage or wear on the CV joints and boots.
3
Examine the wheel bearings for play or damage.
4
Test drive the vehicle to replicate the noise and note the conditions (e.g., sharp turns, speed).
5
Inspect suspension components such as struts and bushings for wear or damage.
6
Check tire condition and alignment for uneven wear or pressure issues.

Solution

1. Preparation

Tools Required: Jack and jack stands, wheel chocks, socket set, torque wrench.
Safety Warnings: Ensure the vehicle is on a flat surface and secured with wheel chocks before lifting.

2. Inspect and Replace CV Joints

Raise the vehicle and remove the front wheels using a socket set.
Visually inspect the CV joints and boots for tears or grease leakage.
If damaged, remove the CV axle:
- Unscrew the retaining bolts at the transmission side and wheel hub.
- Carefully pull the axle out.
Install the new CV axle:
- Align it properly and push it into place until it clicks.
- Reinstall the retaining bolts and torque them to manufacturer specifications.

3. Check and Replace Wheel Bearings

With the wheel removed, grab the wheel hub and check for play.
If there is excessive play, remove the hub assembly:
- Remove the brake caliper and rotor.
- Unscrew the wheel hub mounting bolts.
Replace the wheel bearing:
- Press the new bearing into the hub using a bearing press or hammer (use a proper tool to avoid damage).
Reassemble the hub and torque bolts to specifications.

4. Examine and Repair Suspension Components

Inspect struts and bushings for signs of wear or damage.
Replace any worn struts:
- Remove the strut assembly by unscrewing the upper mounts and lower bolts.
- Install the new strut, making sure to torque all bolts to specifications.