my Honda Civic 10th Generation (2016-2021) makes a grinding noise when turning, what's wrong?

Honda Civic 11th Generation (2022-Present)

Error Codes

2-4 hours

Time

medium

Difficulty

medium

Severity

3 min read

538 words

Problem Statement

Diagnose and fix grinding noise when turning in Honda Civic 10th Generation (2016-2021). Step-by-step guide with symptoms, diagnostic steps, and repair instructions.

Affected Component

Suspension

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on electrical systems.
•Ensure the vehicle is securely lifted and supported before working underneath.

Symptoms

•Grinding noise during turns
•Increased steering effort
•Vibration in the steering wheel
•Unusual tire wear
•Loose or wobbly steering feel

Diagnostic Steps

1
Inspect the power steering fluid level and condition; top off or replace if necessary.
2
Check for any visible damage or wear on the CV joints and boots.
3
Lift the vehicle and inspect the wheel bearings for play or roughness.
4
Examine the suspension components (control arms, bushings, and struts) for damage or wear.
5
Test drive the vehicle while listening for noise changes with varying steering angles.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Jack
•Jack stands
•Socket set
•Torque wrench
•Pry bar
•Bearing puller
•CV joint grease

Parts Required

•CV joints (if damaged)
•Wheel bearings (if needed)
•Suspension components (if worn)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Inspect the power steering fluid level and condition; top off or replace if necessary.
2
Check for any visible damage or wear on the CV joints and boots.
3
Lift the vehicle and inspect the wheel bearings for play or roughness.
4
Examine the suspension components (control arms, bushings, and struts) for damage or wear.
5
Test drive the vehicle while listening for noise changes with varying steering angles.

Solution

1. Preparation

Gather necessary tools and parts.
Park the vehicle on a level surface and engage the parking brake.
Disconnect the negative battery terminal if working on electrical components.

2. Inspect and Replace CV Joints

Tools Required: Jack, jack stands, socket set, torque wrench, pry bar, CV joint grease.
Raise the front of the vehicle and secure it with jack stands.
Remove the wheel to gain access to the CV joint.
Inspect the CV joint and boot for cracking or leaks; if damaged, proceed with replacement.
Remove the axle nut using a socket set and pull the CV axle from the hub.
Replace the CV joint and apply new grease.
Reinstall the CV axle and tighten the axle nut to the manufacturer’s specified torque.

3. Check and Replace Wheel Bearings (if necessary)

Tools Required: Bearing puller, socket set, torque wrench.
With the wheel still removed, check for play in the wheel bearings by rocking the wheel.
If play is detected, remove the hub assembly.
Use a bearing puller to remove the old bearing.
Install the new wheel bearing and reassemble the hub assembly, ensuring proper torque specifications are met.

4. Inspect and Replace Suspension Components (if necessary)

Tools Required: Socket set, torque wrench, pry bar.
Examine the control arms and bushings for any signs of wear or damage.
If any components are found to be defective, remove the affected part using a socket set and replace it with a new component.
Ensure all bolts are torqued to the manufacturer's specifications.