my Honda Civic 10th Generation (2016-2021) has a clicking sound when turning, how to fix it?

Honda Civic 11th Generation (2022-Present)

Error Codes

2-4 hours

Time

medium

Difficulty

medium

Severity

3 min read

535 words

Problem Statement

Learn how to diagnose and fix a clicking sound when turning in a Honda Civic 10th Generation (2016-2021). Step-by-step guide with diagnostic procedures and repair instructions.

Affected Component

Suspension

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect battery before working on electrical systems.
•Use jack stands to secure the vehicle when working underneath.

Symptoms

•Clicking noise when turning the steering wheel
•Noise may increase with sharper turns
•Possible vibration felt through the steering wheel
•No visible damage to tires or wheels
•Lack of power steering fluid might lead to additional noise

Diagnostic Steps

1
Inspect the front axle and CV joints for any signs of wear or damage.
2
Check the power steering fluid level and condition.
3
Examine the suspension components, including struts and control arms, for play or wear.
4
Test drive the vehicle to replicate the clicking sound while turning in both directions.
5
Remove the wheel and inspect the brake components for any issues that could cause noise.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Socket set
•Jack stands
•Jack
•Breaker bar
•Torque wrench

Parts Required

•New CV joint (if damaged)
•Replacement struts or control arms (if worn)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Inspect the front axle and CV joints for any signs of wear or damage.
2
Check the power steering fluid level and condition.
3
Examine the suspension components, including struts and control arms, for play or wear.
4
Test drive the vehicle to replicate the clicking sound while turning in both directions.
5
Remove the wheel and inspect the brake components for any issues that could cause noise.

Solution

1. Preparation

Gather all necessary tools and parts.
Ensure the vehicle is parked on a level surface and the ignition is off.
Disconnect the battery before working on electrical components.

2. Inspect and Replace CV Joints

Remove the Wheel
- Use a socket set to remove the lug nuts and take off the wheel.
- Tools Required: Socket set, jack stands, jack.
Inspect the CV Joint Boot
- Check the boot for tears or leaks.
- If damaged, proceed to replace the CV joint.
Remove the CV Joint
- Disconnect the axle nut using a breaker bar.
- Remove any retaining clips or bolts that secure the CV axle to the hub.
- Carefully pull the CV axle out of the transmission.
Install the New CV Joint
- Insert the new CV joint into the transmission and secure it with the retaining clips and axle nut.
- Torque the axle nut to the manufacturer's specifications (usually around 130 ft-lbs, but check specific service manual).

3. Inspect Suspension Components

Check Struts and Control Arms
- Look for any signs of wear, such as excessive play in bushings or strut mounts.
- Replace any worn components with new parts.

4. Reassemble and Test

Reattach the Wheel
- Place the wheel back onto the hub and hand-tighten the lug nuts.
- Lower the vehicle and then torque the lug nuts to the manufacturer's specifications (typically 80-100 ft-lbs).
Reconnect Battery
- Reconnect the battery after ensuring all repairs are completed.