how to fix Honda Civic 10th Generation (2016-2021) interior lights staying on

Honda Civic 11th Generation (2022-Present)

Error Codes

1-2 hours

Time

medium

Difficulty

medium

Severity

3 min read

521 words

Problem Statement

Learn how to diagnose and fix the issue of interior lights staying on in Honda Civic 10th Generation (2016-2021). Step-by-step guide included.

Affected Component

Electrical

Estimated Time

1-2 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on electrical systems to prevent short circuits.
•Allow the vehicle to cool down if working on components near heat sources.

Symptoms

•Interior lights do not turn off after closing the doors
•Dome light stays on while driving
•Battery draining when the vehicle is parked
•Overhead lights flicker intermittently
•Door ajar warning light illuminated on the dashboard

Diagnostic Steps

1
Inspect the door switches for proper operation and alignment.
2
Check the interior light switch position (ensure it is set to 'door' or 'off').
3
Scan for any error codes related to the body control module (BCM) using an OBD-II scanner.
4
Test the battery voltage to rule out a weak battery causing erratic behavior.
5
Inspect the wiring and connectors for any corrosion or damage around the door latch and BCM.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Multimeter
•Screwdriver set

Parts Required

•Replacement door switch (if faulty)
•Electrical connectors (if damaged)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Inspect the door switches for proper operation and alignment.
2
Check the interior light switch position (ensure it is set to 'door' or 'off').
3
Scan for any error codes related to the body control module (BCM) using an OBD-II scanner.
4
Test the battery voltage to rule out a weak battery causing erratic behavior.
5
Inspect the wiring and connectors for any corrosion or damage around the door latch and BCM.

Solution

1. Preparation

Gather tools and parts: OBD-II scanner, multimeter, screwdriver set, and replacement door switch (if needed).
Disconnect the vehicle battery to ensure safety while working on electrical components.

2. Inspect and Adjust Door Switches

Locate the door switches, typically located on the door latch mechanism.
Remove the door panel if necessary to access the switch.
Clean any dirt or debris around the switches and ensure they are not stuck.
Test the switches using a multimeter for continuity when the door is closed and open.
Adjust or replace any faulty switches.

3. Check and Replace Wiring/Connectors

Inspect the wiring harness connected to the door switches and BCM for any signs of wear or damage.
Repair any frayed wires or loose connections using electrical tape or heat shrink tubing.
Replace any corroded connectors with new ones to ensure proper electrical contact.

4. Reset the BCM

Reconnect the vehicle battery.
Use the OBD-II scanner to clear any error codes related to the BCM.
Perform a reset of the BCM by disconnecting the battery for about 10 minutes before reconnecting it.

5. Test Interior Lights Functionality

Open and close each door to ensure the interior lights function correctly.
Verify that the lights turn off when all doors are closed and when the vehicle is locked.