how to fix grinding noise when turning in Honda Civic 9th Generation (2012-2015)

Honda Civic 11th Generation (2022-Present)

Error Codes

2-4 hours

Time

medium

Difficulty

high

Severity

3 min read

558 words

⚠️ Safety Warning

This issue requires immediate attention. If you are not experienced with automotive repairs, consult a professional mechanic. Working on critical systems can be dangerous.

Problem Statement

Learn how to diagnose and fix grinding noise when turning in Honda Civic 2012-2015. Step-by-step guide with symptoms, diagnostic steps, and repair instructions.

Affected Component

Steering

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Always disconnect the battery before working on electrical systems.
•Allow the engine to cool before working on any components near the engine.

Symptoms

•Grinding noise audible during turns
•Increased steering effort or stiffness
•Vibration in the steering wheel
•Uneven tire wear
•Fluid leaks around the power steering system

Diagnostic Steps

1
Inspect the power steering fluid level and condition.
2
Check for visible leaks in the power steering system.
3
Examine the condition of the steering rack and tie rod ends for wear or damage.
4
Test the wheel bearings for play or roughness by lifting the vehicle and spinning the wheels.
5
Inspect the CV joints and boots for any signs of wear or damage.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Fluid siphon
•Socket set
•Torque wrench
•Ball joint separator
•CV joint removal tool
•Bearing puller

Parts Required

•Power steering fluid
•Tie rod ends (if worn)
•CV joints (if damaged)
•Wheel bearings (if worn)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Inspect the power steering fluid level and condition.
2
Check for visible leaks in the power steering system.
3
Examine the condition of the steering rack and tie rod ends for wear or damage.
4
Test the wheel bearings for play or roughness by lifting the vehicle and spinning the wheels.
5
Inspect the CV joints and boots for any signs of wear or damage.

Solution

1. Preparation

Gather tools and parts for the repair.
Ensure the vehicle is parked on a level surface and the engine is turned off.
Disconnect the battery for safety.

2. Inspect and Replace Power Steering Fluid

Tools Required: Fluid siphon, new power steering fluid.
Use a fluid siphon to remove old power steering fluid from the reservoir.
Refill with the manufacturer-recommended power steering fluid.
Start the engine and turn the steering wheel from lock to lock to circulate the new fluid.

3. Replace Damaged Components

A. Tie Rod Ends

Tools Required: Socket set, torque wrench, ball joint separator.
Lift the vehicle and remove the front wheels.
Locate the tie rod ends and inspect them for play.
Remove the tie rod end nut and separate it from the steering knuckle using a ball joint separator.
Install the new tie rod end and torque the nut to the manufacturer's specifications.

B. CV Joints

Tools Required: Socket set, CV joint removal tool.
If CV joints are damaged, remove the axle nut and disconnect the lower control arm.
Slide the axle out of the transmission and replace the CV joint.
Reassemble and torque all components to the specified values.

4. Inspect and Replace Wheel Bearings (if necessary)

Tools Required: Bearing puller, socket set, torque wrench.
Remove the wheel and brake components to access the hub.
Use a bearing puller to remove the old wheel bearing from the hub.
Install the new wheel bearing and reassemble the hub, ensuring all fasteners are torqued to specification.