my Honda Civic 10th Generation (2016-2021) has a ticking noise from the engine, what's wrong

Honda Civic 10th Generation (2016-2021)

Error Codes

2-4 hours

Time

medium

Difficulty

medium

Severity

3 min read

491 words

Problem Statement

Learn how to diagnose and fix engine ticking noise in Honda Civic 10th Generation (2016-2021). Step-by-step guide with diagnostic procedures and repair instructions.

Affected Component

Engine

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on electrical systems.
•Allow the engine to cool before opening the oil drain plug.

Symptoms

•Ticking noise coming from the engine compartment
•Possible loss of power during acceleration
•Engine misfires or rough idling
•Decreased fuel efficiency
•Check engine light illuminated (may occur)

Diagnostic Steps

1
Scan for error codes using an OBD-II scanner to identify any stored trouble codes.
2
Inspect the oil level and condition to ensure proper lubrication of engine components.
3
Check for loose or damaged components in the engine bay, including heat shields and covers.
4
Listen closely to the ticking noise with a mechanic’s stethoscope to localize the source.
5
Inspect the valve train components (e.g., lifters, rocker arms) for wear or damage.
6
Perform a compression test to check for potential internal engine problems.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Mechanic’s stethoscope
•Socket set
•Torque wrench
•Compression tester

Parts Required

•Engine oil (0W-20)
•Oil filter
•Valve lifters (if replacement is necessary)
•Valve cover gasket

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Scan for error codes using an OBD-II scanner to identify any stored trouble codes.
2
Inspect the oil level and condition to ensure proper lubrication of engine components.
3
Check for loose or damaged components in the engine bay, including heat shields and covers.
4
Listen closely to the ticking noise with a mechanic’s stethoscope to localize the source.
5
Inspect the valve train components (e.g., lifters, rocker arms) for wear or damage.
6
Perform a compression test to check for potential internal engine problems.

Solution

1. Preparation

Tools Required: OBD-II scanner, mechanic’s stethoscope, socket set, torque wrench, compression tester.
Ensure the vehicle is parked on a level surface and the engine is cool before starting.
Disconnect the battery to avoid electrical shorts.

2. Change Engine Oil and Filter

Sub-steps:
1. Remove the oil drain plug using a socket set and drain the old oil into a suitable container.
2. Replace the oil filter with a new one, ensuring to lubricate the rubber gasket with new oil.
3. Reinstall the drain plug and torque to the manufacturer’s specifications.
4. Fill the engine with the recommended type and amount of oil (typically 0W-20 for Honda).

3. Inspect and Replace Valve Lifters (if necessary)

Sub-steps:
1. Remove the valve cover by loosening the bolts with a socket set.
2. Inspect the valve lifters for wear; replace them if they show signs of damage.
3. Reinstall the valve cover with a new gasket, ensuring it's properly sealed and torqued to specifications.

4. Reassemble and Test

Sub-steps:
1. Reconnect the battery and check all connections.
2. Start the engine and listen for any remaining noises.
3. If the ticking noise persists, further internal inspection may be necessary.