my Honda Civic 10th Generation (2016-2021) dies while driving what's causing it

Honda Civic 10th Generation (2016-2021)

Error Codes

2-4 hours

Time

medium

Difficulty

high

Severity

3 min read

466 words

⚠️ Safety Warning

This issue requires immediate attention. If you are not experienced with automotive repairs, consult a professional mechanic. Working on critical systems can be dangerous.

Problem Statement

Learn how to diagnose and fix engine stalling issues in Honda Civic 10th Generation (2016-2021). Step-by-step guide with diagnostic procedures and repair instructions.

Affected Component

Engine

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on electrical systems.
•Allow the engine to cool before working on the throttle body.

Symptoms

•Check engine light illuminated
•Engine stalling unexpectedly
•Rough idle before stalling
•Loss of power during acceleration
•Difficulty restarting the engine after stalling

Diagnostic Steps

1
Scan for error codes using an OBD-II scanner to identify any trouble codes.
2
Check fuel pump operation by listening for the pump's hum when the ignition is turned on without starting the engine.
3
Inspect the fuel filter for clogs or blockages.
4
Test the ignition coils for proper resistance using a multimeter.
5
Inspect the battery and charging system, checking voltage and connections.
6
Verify the condition of the throttle position sensor (TPS) by checking its output with a multimeter.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Multimeter
•Socket set
•Screwdriver set

Parts Required

•Fuel pump (if faulty)
•Ignition coils (if faulty)
•Throttle position sensor (if faulty)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Scan for error codes using an OBD-II scanner to identify any trouble codes.
2
Check fuel pump operation by listening for the pump's hum when the ignition is turned on without starting the engine.
3
Inspect the fuel filter for clogs or blockages.
4
Test the ignition coils for proper resistance using a multimeter.
5
Inspect the battery and charging system, checking voltage and connections.
6
Verify the condition of the throttle position sensor (TPS) by checking its output with a multimeter.

Solution

1. Preparation

Gather the necessary tools and parts.
Ensure the vehicle is parked on a flat surface and the engine is off.
Disconnect the battery to ensure safety.

2. Fuel System Inspection

Sub-step 1: Remove the fuel pump relay from the fuse box.
Sub-step 2: Jump the terminals to activate the fuel pump and listen for operation.
Sub-step 3: If the pump is silent, replace the fuel pump.
Tools Required: OBD-II scanner, multimeter, socket set.

3. Ignition System Repair

Sub-step 1: Disconnect the ignition coils and remove them from the engine.
Sub-step 2: Test each ignition coil for proper resistance; replace any faulty coils.
Sub-step 3: Reinstall the ignition coils and reconnect them securely.
Tools Required: Multimeter, socket set.

4. Throttle Position Sensor Inspection

Sub-step 1: Locate the throttle position sensor (TPS) on the throttle body.
Sub-step 2: Disconnect the TPS connector and test the output voltage while moving the throttle.
Sub-step 3: Replace the TPS if the voltage does not change smoothly.
Tools Required: Multimeter, socket set.