how to fix my Honda Civic 10th Generation (2016-2021) EPS light

Honda Civic 10th Generation (2016-2021)

Error Codes

2-4 hours

Time

medium

Difficulty

high

Severity

3 min read

501 words

⚠️ Safety Warning

This issue requires immediate attention. If you are not experienced with automotive repairs, consult a professional mechanic. Working on critical systems can be dangerous.

Problem Statement

Learn how to diagnose and fix the EPS light issue on your Honda Civic 10th Generation (2016-2021). Step-by-step guide with tools and tips.

Affected Component

Steering

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on electrical components
•Allow the engine to cool before performing any service

Symptoms

•EPS warning light illuminated on the dashboard
•Difficult steering or reduced steering assist
•Intermittent power steering assist
•No power steering assist at all
•Steering wheel feels heavy or unresponsive

Diagnostic Steps

1
Scan for error codes using an OBD-II scanner to identify any relevant diagnostic trouble codes (DTCs)
2
Check the power steering fluid level and condition; ensure it meets the manufacturer's specifications
3
Inspect the EPS motor and power steering control module for signs of damage or wear
4
Test the EPS system using a multimeter to check for proper voltage and ground at the EPS connector
5
Inspect the steering angle sensor for proper alignment and function
6
Verify connections and wiring for any signs of corrosion or damage

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Socket set
•Torque wrench
•Screwdriver
•Fluid pump
•Multimeter

Parts Required

•Honda Genuine Power Steering Fluid
•EPS motor (if replacement is necessary)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Scan for error codes using an OBD-II scanner to identify any relevant diagnostic trouble codes (DTCs)
2
Check the power steering fluid level and condition; ensure it meets the manufacturer's specifications
3
Inspect the EPS motor and power steering control module for signs of damage or wear
4
Test the EPS system using a multimeter to check for proper voltage and ground at the EPS connector
5
Inspect the steering angle sensor for proper alignment and function
6
Verify connections and wiring for any signs of corrosion or damage

Solution

1. Preparation

Gather necessary tools and parts.
Ensure the vehicle is parked on a level surface with the ignition off.
Disconnect the battery to avoid any electrical shorts.

2. Check and Replace Power Steering Fluid

Tools Required: Fluid pump, funnel, clean rags
Remove the power steering fluid reservoir cap.
Using a fluid pump, extract old fluid from the reservoir.
Inspect the fluid; if it is dark or contaminated, replace it with Honda Genuine Power Steering Fluid.
Fill the reservoir to the appropriate level and replace the cap securely.

3. Inspect and Replace EPS Motor

Tools Required: Socket set, torque wrench, screwdriver
Remove the EPS motor by disconnecting the wiring harness and unbolting it from the steering column.
Inspect the motor for signs of wear or damage.
If necessary, replace the EPS motor with a new one, ensuring to torque the bolts to the manufacturer specifications (typically around 25-30 Nm).
Reconnect the wiring harness securely.

4. Reset EPS System

Tools Required: OBD-II scanner
Reconnect the battery.
Use an OBD-II scanner to clear any stored DTCs related to the EPS.
Follow the scanner instructions to reset the EPS system.