Honda Civic 10th Generation (2016-2021) rear brakes squeaking constantly what to check

Honda Civic 10th Generation (2016-2021)

Error Codes

2-4 hours

Time

medium

Difficulty

medium

Severity

3 min read

569 words

Problem Statement

Learn how to diagnose and fix constant squeaking noise in rear brakes of Honda Civic 10th Generation (2016-2021). Step-by-step guide included.

Affected Component

Brakes

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on electrical systems.
•Allow brakes to cool before working on them after driving.

Symptoms

•Constant squeaking noise when brakes are applied or released
•Reduced braking efficiency
•Vibration felt through the brake pedal
•Brake dust accumulation on the wheels
•Unusual wear on brake pads or rotors

Diagnostic Steps

1
Inspect the rear brake pads for wear and thickness using a caliper gauge.
2
Check the rear rotors for scoring, warping, or uneven surfaces.
3
Examine the brake caliper for proper operation and any signs of sticking.
4
Look for any debris or foreign objects lodged between the brake components.
5
Verify the brake hardware (shims, clips, etc.) for damage or corrosion.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Socket set
•Torque wrench
•Brake grease
•Caliper gauge
•Jack and jack stands

Parts Required

•Brake pads
•Brake rotors (if needed)
•Caliper hardware kit (if necessary)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Inspect the rear brake pads for wear and thickness using a caliper gauge.
2
Check the rear rotors for scoring, warping, or uneven surfaces.
3
Examine the brake caliper for proper operation and any signs of sticking.
4
Look for any debris or foreign objects lodged between the brake components.
5
Verify the brake hardware (shims, clips, etc.) for damage or corrosion.

Solution

1. Preparation

Gather all necessary tools and parts.
Ensure the vehicle is parked on a level surface and the parking brake is engaged.
Disconnect the negative battery cable to ensure safety.

2. Remove Rear Wheel

Using a jack, lift the rear of the vehicle and secure it with jack stands.
Remove the lug nuts with a socket set and take off the rear wheel.

3. Inspect and Replace Brake Pads

Inspect Brake Pads:
- Check the pads for thickness; if they are below 3mm, replace them.
Remove Brake Caliper:
- Use a socket set to remove the caliper mounting bolts.
- Carefully slide the caliper off the rotor and suspend it using a bungee cord.
Remove Brake Pads:
- Slide the old brake pads out of the caliper bracket.
Install New Brake Pads:
- Apply brake grease to the back of the new pads and slide them into the caliper bracket.

4. Check and Replace Brake Rotors (if necessary)

Remove Brake Rotor:
- If the rotor is damaged, remove it by unscrewing the retaining screws (if applicable) and sliding it off the hub.
Install New Brake Rotor:
- Place the new rotor onto the hub, ensuring it fits snugly.

5. Reassemble Components

Reattach the brake caliper over the new pads and rotor.
Tighten the caliper mounting bolts to the manufacturer's torque specifications (typically around 20-25 lb-ft).
Reinstall the rear wheel and hand-tighten the lug nuts.

6. Final Checks

Lower the vehicle and remove the jack stands.
Reconnect the negative battery cable.
Pump the brake pedal a few times to ensure proper pad seating.