why does my Honda Accord make a popping sound when I turn?

Honda Accord 9th Generation (2013-2017)

Error Codes

2-4 hours

Time

medium

Difficulty

medium

Severity

3 min read

514 words

Problem Statement

Learn how to diagnose and fix popping sounds when turning in Honda Accord. Step-by-step guide with diagnostic procedures and repair instructions.

Affected Component

Suspension

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Always use jack stands when working under the vehicle.
•Disconnect the battery before working on electrical components.

Symptoms

•Popping or clicking noise during turns
•Increased vibration in the steering wheel
•Difficulty steering or loss of steering response
•Uneven tire wear
•Knocking noise when going over bumps

Diagnostic Steps

1
Inspect CV joints for wear or damage visually.
2
Check the condition of the wheel bearings by lifting the vehicle and spinning the wheel.
3
Test the suspension components for play or damage, including struts and bushings.
4
Examine the steering linkage for any signs of wear or looseness.
5
Verify tire condition and alignment settings.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Jack and jack stands
•Socket set
•Torque wrench
•Pry bar
•Flashlight

Parts Required

•CV joint (if damaged)
•Wheel bearing (if worn)
•Suspension bushings/struts (if necessary)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Inspect CV joints for wear or damage visually.
2
Check the condition of the wheel bearings by lifting the vehicle and spinning the wheel.
3
Test the suspension components for play or damage, including struts and bushings.
4
Examine the steering linkage for any signs of wear or looseness.
5
Verify tire condition and alignment settings.

Solution

1. Preparation

Tools Required: Jack and jack stands, socket set, torque wrench, pry bar, and a flashlight.
Ensure the vehicle is parked on a level surface and the engine is off.
Disconnect the battery to prevent any electrical issues.

2. Inspect and Replace CV Joints

Sub-steps:
1. Lift the front of the vehicle using a jack and secure with jack stands.
2. Remove the wheel to access the CV joint.
3. Inspect the CV joint boot for tears or grease leakage. If damaged, proceed to replace.
4. Use a socket set to remove the axle nut and the retaining bolts for the CV joint.
5. Install the new CV joint, torque the axle nut to the manufacturer's specifications (typically around 150 ft-lbs).
6. Reinstall the wheel and lower the vehicle.

3. Inspect and Replace Wheel Bearings

Sub-steps:
1. With the wheel removed, check for play in the wheel bearing by shaking the wheel.
2. If there's excessive movement, remove the bearing hub using the socket set.
3. Replace the wheel bearing with a new one, ensuring it is properly seated.
4. Reassemble the hub and torque the mounting bolts to the proper specification (consult service manual for exact values).

4. Inspect and Replace Suspension Components

Sub-steps:
1. Check the struts and bushings for wear; use a pry bar to check for play.
2. If worn, remove the strut assembly using the socket set.
3. Replace the strut or bushing as needed, ensuring all connections are secure.
4. Reassemble the suspension components, making sure to torque all bolts to specification.