my Honda Accord makes a shuddering noise when accelerating what's wrong

Honda Accord 9th Generation (2013-2017)

Error Codes

2-4 hours

Time

medium

Difficulty

medium

Severity

3 min read

544 words

Problem Statement

Learn how to diagnose and fix shuddering noise during acceleration in Honda Accord. Step-by-step guide with diagnostic procedures and repair instructions.

Affected Component

Transmission

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on electrical systems.
•Allow the engine to cool before opening the radiator or working near hot components.

Symptoms

•Shuddering or vibrating noise when accelerating
•Possible loss of power during acceleration
•Unusual engine RPM fluctuations
•Check engine light illuminated
•Poor fuel economy

Diagnostic Steps

1
Scan for error codes using an OBD-II scanner to identify any stored trouble codes.
2
Inspect the transmission fluid level and condition for any signs of contamination or low fluid.
3
Check for any visible damage or wear on engine and transmission mounts.
4
Conduct a road test to replicate the shuddering noise and observe the behavior under different acceleration conditions.
5
Examine the drive belts and pulleys for wear or misalignment.
6
Inspect the condition of the CV joints and axles for any signs of damage or wear.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Socket set
•Torque wrench
•Jack and jack stands

Parts Required

•Transmission fluid
•Engine/transmission mounts
•CV joint/axle

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Scan for error codes using an OBD-II scanner to identify any stored trouble codes.
2
Inspect the transmission fluid level and condition for any signs of contamination or low fluid.
3
Check for any visible damage or wear on engine and transmission mounts.
4
Conduct a road test to replicate the shuddering noise and observe the behavior under different acceleration conditions.
5
Examine the drive belts and pulleys for wear or misalignment.
6
Inspect the condition of the CV joints and axles for any signs of damage or wear.

Solution

1. Preparation

Gather tools and parts for the repair.
Ensure the vehicle is parked on a level surface and the engine is off.
Disconnect the battery to prevent any electrical issues during the repair.

2. Inspect and Replace Transmission Fluid

Sub-steps:
1. Locate the transmission dipstick and remove it.
2. Check the fluid level and condition (should be red and clear; brown or burnt indicates replacement).
3. If necessary, drain the transmission fluid using a wrench to remove the drain plug.
4. Replace the drain plug and refill with new transmission fluid according to the manufacturer's specifications.
5. Start the engine and allow it to run for a few minutes, then recheck the fluid level.

3. Check and Replace Engine/Transmission Mounts

Sub-steps:
1. Visually inspect engine and transmission mounts for cracks, separation, or excessive wear.
2. If damaged, use a socket set to remove the bolts securing the mounts.
3. Replace with new mounts, ensuring proper alignment.
4. Torque bolts to the manufacturer’s specifications.

4. Inspect and Replace CV Joints/Axles

Sub-steps:
1. Lift the vehicle using a jack and secure it with jack stands.
2. Inspect CV joints for any grease leaks or torn boots.
3. If damaged, remove the axle nut using a socket and pull the axle out.
4. Install the new axle, ensuring it is properly seated, and replace the axle nut, torquing it to specifications.