my Honda Accord makes a grinding noise when turning, what could it be?

Honda Accord 9th Generation (2013-2017)

Error Codes

2-4 hours

Time

medium

Difficulty

high

Severity

3 min read

496 words

⚠️ Safety Warning

This issue requires immediate attention. If you are not experienced with automotive repairs, consult a professional mechanic. Working on critical systems can be dangerous.

Problem Statement

Learn how to diagnose and fix grinding noise when turning in Honda Accord. Step-by-step guide with diagnostic procedures and repair instructions.

Affected Component

Steering

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on electrical systems.
•Ensure the vehicle is securely lifted and supported before working underneath it.

Symptoms

•Grinding noise during left or right turns
•Vibration in the steering wheel when turning
•Decreased steering response
•Potential clunking noise when going over bumps
•Uneven tire wear

Diagnostic Steps

1
Inspect the power steering fluid level and condition.
2
Check for leaks in the power steering system.
3
Examine the CV joints and boots for damage or wear.
4
Inspect the wheel bearings for play or grinding.
5
Assess the condition of the suspension components (struts, control arms).
6
Check the brake pads and rotors for any signs of abnormal wear.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Jack and jack stands
•Socket set
•Torque wrench
•Bearing puller
•Screwdrivers
•Pliers

Parts Required

•Power steering fluid
•CV joint (if damaged)
•Wheel bearing (if worn)
•Suspension components (if necessary)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Inspect the power steering fluid level and condition.
2
Check for leaks in the power steering system.
3
Examine the CV joints and boots for damage or wear.
4
Inspect the wheel bearings for play or grinding.
5
Assess the condition of the suspension components (struts, control arms).
6
Check the brake pads and rotors for any signs of abnormal wear.

Solution

1. Preparation

Gather necessary tools and parts.
Ensure the vehicle is parked on a level surface and turn off the engine.
Disconnect the battery for safety, if working on electrical components.

2. Inspect and Replace Power Steering Fluid

Check fluid level: Remove the power steering reservoir cap and inspect the fluid.
If low, add manufacturer-recommended power steering fluid.
If contaminated (dark or gritty), drain and refill the system.

3. Examine and Replace CV Joints

Raise the front of the vehicle using a jack and secure with jack stands.
Remove the wheel to access the CV joint.
Inspect the CV boot for tears or leaks; replace if damaged.
If the CV joint itself is worn, remove the axle nut and disconnect the CV joint from the transmission or hub assembly.
Install a new CV joint and reassemble.

4. Check and Replace Wheel Bearings

Spin the wheel by hand; if you hear grinding, the wheel bearing may need replacement.
Remove the wheel and brake caliper to access the hub.
Remove the hub assembly and replace the wheel bearing using a bearing puller.
Reassemble the wheel and brakes.

5. Inspect Suspension Components

Visually inspect struts, control arms, and bushings for wear.
Replace any damaged or worn components following manufacturer specifications.
Torque bolts to manufacturer's specifications.