why does my Honda Accord 10th Generation (2018-2022) shake when I accelerate

Honda Accord 8th Generation (2008-2012)

Error Codes

2-4 hours

Time

medium

Difficulty

medium

Severity

3 min read

500 words

Problem Statement

Learn how to diagnose and fix shaking during acceleration in Honda Accord 10th Generation (2018-2022). Step-by-step guide with diagnostic procedures and repair instructions.

Affected Component

Suspension

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Always disconnect the battery before performing repairs on electrical components.
•Ensure the vehicle is securely supported when working underneath.

Symptoms

•Vibration felt through the steering wheel
•Shaking in the seat or floor during acceleration
•Increased noise from the engine or drivetrain
•Possible loss of power during acceleration
•Uneven tire wear (may be observed over time)

Diagnostic Steps

1
Inspect tire condition and pressure for uneven wear or low inflation.
2
Check wheel alignment and balance by taking the vehicle to a professional.
3
Scan the vehicle’s computer for any stored error codes using an OBD-II scanner.
4
Inspect the engine and transmission mounts for signs of wear or damage.
5
Examine the driveshaft and CV joints for any signs of wear or failure.
6
Check for any loose or damaged suspension components.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Tire pressure gauge
•Socket set
•Torque wrench

Parts Required

•New tires (if necessary)
•Engine and transmission mounts (if required)
•Any necessary driveshaft or CV joint components (if applicable)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Inspect tire condition and pressure for uneven wear or low inflation.
2
Check wheel alignment and balance by taking the vehicle to a professional.
3
Scan the vehicle’s computer for any stored error codes using an OBD-II scanner.
4
Inspect the engine and transmission mounts for signs of wear or damage.
5
Examine the driveshaft and CV joints for any signs of wear or failure.
6
Check for any loose or damaged suspension components.

Solution

1. Preparation

Gather necessary tools and parts.
Park the vehicle on a level surface and engage the parking brake.
Disconnect the battery to ensure safety while working on electrical components.

2. Tire Inspection and Adjustment

Sub-steps:
1. Inspect all tires for uneven wear or damage.
2. Check tire pressure using a tire gauge and inflate to the manufacturer's recommended PSI.
3. Replace any damaged tires as needed.
4. Consider rotating the tires to promote even wear.

3. Wheel Alignment and Balancing

Sub-steps:
1. Take the vehicle to a professional alignment shop.
2. Have the technician perform a four-wheel alignment and balance the tires.
3. Confirm the alignment specifications meet manufacturer standards.

4. Inspect and Replace Engine and Transmission Mounts

Sub-steps:
1. Visually inspect engine and transmission mounts for cracks or degradation.
2. If damaged, remove the old mounts using a socket set and install new mounts.
3. Torque new mounts to manufacturer specifications (usually specified in the repair manual).

5. Check Driveshaft and CV Joints

Sub-steps:
1. Inspect the driveshaft for any visible damage or excessive play.
2. Check CV joints for torn boots or grease leakage.
3. Replace any faulty components as needed, ensuring proper installation and torque settings.