why does my Honda Accord 10th Generation (2018-2022) make a popping noise when turning

Honda Accord 8th Generation (2008-2012)

Error Codes

2-4 hours

Time

medium

Difficulty

medium

Severity

3 min read

496 words

Problem Statement

Learn how to diagnose and fix popping noise when turning in Honda Accord 10th Generation (2018-2022). Step-by-step guide with diagnostic procedures and repair instructions.

Affected Component

Suspension

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on electrical systems.
•Ensure the vehicle is securely lifted and supported before working underneath.

Symptoms

•Popping or clicking noise during turns
•Noise increases with sharper turns or when under load
•Vibration felt in the steering wheel
•Possible clunking when driving over bumps
•Uneven tire wear or visible damage to suspension components

Diagnostic Steps

1
Inspect the front suspension components, including control arms, ball joints, and tie rods for wear or damage.
2
Check the CV joints for any signs of tears or excessive play.
3
Examine the wheel bearings for roughness or play by spinning the wheel and listening for noise.
4
Lift the vehicle and shake the wheels to test for any movement in the suspension components.
5
Use an OBD-II scanner to check for any related fault codes that might indicate steering or suspension issues.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Socket set
•Torque wrench
•Jack and jack stands
•Pry bar

Parts Required

•CV joint assembly (if damaged)
•Control arms or ball joints (if worn)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Inspect the front suspension components, including control arms, ball joints, and tie rods for wear or damage.
2
Check the CV joints for any signs of tears or excessive play.
3
Examine the wheel bearings for roughness or play by spinning the wheel and listening for noise.
4
Lift the vehicle and shake the wheels to test for any movement in the suspension components.
5
Use an OBD-II scanner to check for any related fault codes that might indicate steering or suspension issues.

Solution

1. Preparation

Ensure the vehicle is parked on a flat surface and the engine is off.
Gather tools and necessary components.
Wear safety gloves and goggles.

2. Inspect and Replace CV Joints

Inspect the CV Joints
- Remove the wheel using a socket set to access the CV axle.
- Check for any visible tears in the CV boot; if damaged, the joint may need replacement.
Replace if Necessary
- Remove the axle nut using a torque wrench.
- Detach the CV axle from the transmission and wheel hub.
- Install the new CV joint by reversing the removal steps.
- Torque the axle nut to the manufacturer’s specifications (typically around 130 ft-lbs).

3. Replace Worn Suspension Components

Inspect Suspension Parts
- Check control arms, ball joints, and tie rods for wear.
Replacement Steps
- Remove any bolts securing the control arm or joint using a socket set.
- Replace the worn part with a new one.
- Reattach using the manufacturer-specified torque values (typically around 50-70 ft-lbs for control arm bolts).

4. Test Drive

After reassembly, lower the vehicle and conduct a test drive.
Listen for the popping noise to confirm the issue has been resolved.