why does my Honda Accord 10th Generation (2018-2022) make a grinding noise when turning

Honda Accord 8th Generation (2008-2012)

Error Codes

2-4 hours

Time

medium

Difficulty

medium

Severity

3 min read

538 words

Problem Statement

Learn to diagnose and fix grinding noise when turning in Honda Accord 10th Generation (2018-2022). Step-by-step guide with symptoms and solutions.

Affected Component

Steering

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Always ensure the vehicle is securely supported on jack stands before working underneath.
•Disconnect the battery before performing any electrical work.

Symptoms

•Grinding noise when turning the steering wheel
•Difficulty in steering or a feeling of resistance
•Uneven tire wear
•Vibration in the steering wheel
•Possible fluid leaks under the vehicle

Diagnostic Steps

1
Inspect the power steering fluid level and condition.
2
Check for visible damage or wear on the steering components (tie rods, bushings).
3
Inspect the CV joints and axles for any signs of wear or damage.
4
Examine the wheel bearings for play or roughness.
5
Test drive the vehicle to replicate the grinding noise and note the conditions under which it occurs.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Socket set
•Torque wrench
•Jack and jack stands
•Screwdrivers
•Fluid extractor

Parts Required

•Power steering fluid
•CV joint or axle (if damaged)
•Tie rod ends (if worn)
•Wheel bearings (if necessary)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Inspect the power steering fluid level and condition.
2
Check for visible damage or wear on the steering components (tie rods, bushings).
3
Inspect the CV joints and axles for any signs of wear or damage.
4
Examine the wheel bearings for play or roughness.
5
Test drive the vehicle to replicate the grinding noise and note the conditions under which it occurs.

Solution

1. Preparation

Gather all necessary tools and parts.
Park the vehicle on a flat surface and engage the parking brake.
Disconnect the negative battery terminal to prevent electrical issues.

2. Inspect and Replace Power Steering Fluid

Locate the power steering reservoir.
Remove the cap and check fluid level; if low, top off with the manufacturer-recommended fluid.
If the fluid is dirty, drain the old fluid from the reservoir and replace it with fresh fluid.

3. Inspect Steering Components

Raise the front of the vehicle using a jack and secure it with jack stands.
Remove the front wheels for better access to steering components.
Inspect tie rods and bushings for wear; replace any damaged parts.

4. Check CV Joints and Axles

Examine the CV joints for any tears in the rubber boot or grease leakage.
If damaged, replace the CV joint or axle as required.
Ensure that the axle nuts are torqued to the manufacturer specifications after replacement.

5. Inspect Wheel Bearings

Spin the wheel by hand and listen for noise; if grinding is heard, replace the wheel bearing.
Remove the hub assembly if needed to access the wheel bearings.
Clean the bearing housing and install new bearings, ensuring proper lubrication.

6. Reassemble and Lower Vehicle

Reinstall the front wheels and torque the lug nuts to the manufacturer's specifications.
Reconnect the battery terminal.
Lower the vehicle and perform a test drive to ensure the issue is resolved.