what causes my Honda Accord 10th Generation (2018-2022) to shake while braking

Honda Accord 8th Generation (2008-2012)

Error Codes

2-4 hours

Time

medium

Difficulty

high

Severity

3 min read

568 words

⚠️ Safety Warning

This issue requires immediate attention. If you are not experienced with automotive repairs, consult a professional mechanic. Working on critical systems can be dangerous.

Problem Statement

Learn how to diagnose and fix brake shaking issues in Honda Accord 10th Generation (2018-2022). Step-by-step guide with diagnostic procedures and repair instructions.

Affected Component

Brakes

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Always wear safety glasses and gloves when working on brakes.
•Ensure the vehicle is securely raised and supported before working underneath.

Symptoms

•Steering wheel shakes when brakes are applied
•Pulsation felt through the brake pedal
•Uneven wear on brake pads or rotors
•Increased stopping distance
•Possible noise during braking (grinding or squeaking)

Diagnostic Steps

1
Inspect brake pads for wear and unevenness.
2
Check brake rotors for warping or scoring using a dial indicator.
3
Examine wheel alignment and balance.
4
Inspect suspension components (e.g., control arms, bushings) for damage or wear.
5
Verify tire condition and pressure for uniformity.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Socket set
•Jack
•Jack stands
•Torque wrench
•Dial indicator
•Brake pad spreader (if needed)
•Impact wrench (if screws are tight)

Parts Required

•New brake pads
•Brake rotors (if warped or worn beyond specs)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Solution

1. Preparation

Gather tools and parts required for the repair.
Ensure the vehicle is parked on a level surface and set the parking brake.
Disconnect the battery to prevent any electrical issues.

2. Remove Wheel

Sub-steps:
- Loosen lug nuts using a socket wrench before lifting the vehicle.
- Lift the vehicle using a jack and secure it with jack stands.
- Remove the lug nuts and take off the wheel.
Tools Required: Socket set, jack, jack stands.

3. Inspect and Replace Brake Pads

Sub-steps:
- Remove the caliper bolts using a socket wrench.
- Carefully slide the caliper off the rotor and support it without stressing the brake line.
- Remove the old brake pads from the caliper bracket.
- Install new brake pads, ensuring they are properly seated.
Tools Required: Socket set, brake pad spreader (if needed).

4. Check and Resurface or Replace Rotors

Sub-steps:
- Remove the rotor by unscrewing the retaining screws (if applicable) and sliding it off the hub.
- Measure rotor thickness and check for warping with a dial indicator.
- If warped, either resurface the rotors or replace them with new ones.
Tools Required: Dial indicator, impact wrench (if screws are tight).

5. Reassemble and Reinstall

Sub-steps:
- Reinstall the rotor (if removed) and secure it with retaining screws.
- Reattach the caliper over the new brake pads and tighten caliper bolts to manufacturer specifications (typically 20-30 ft-lbs).
- Reinstall the wheel and hand-tighten the lug nuts.
Tools Required: Torque wrench.

6. Lower Vehicle and Final Checks

Sub-steps:
- Lower the vehicle from jack stands.
- Tighten the lug nuts to the manufacturer’s torque specifications (typically 80-100 ft-lbs).
- Reconnect the battery.
Tools Required: Torque wrench, socket set.