my Honda Accord 10th Generation (2018-2022) makes a popping sound when turning

Honda Accord 8th Generation (2008-2012)

Error Codes

2-4 hours

Time

medium

Difficulty

medium

Severity

3 min read

508 words

Problem Statement

Learn how to diagnose and fix a popping sound when turning in a Honda Accord 10th Generation (2018-2022). Step-by-step guide with diagnostic procedures and repair instructions.

Affected Component

Suspension

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Always secure the vehicle on jack stands before working underneath it.
•Wear safety glasses to protect from debris while inspecting components.

Symptoms

•Popping or clicking noise during turns
•Noise may increase with speed or sharpness of the turn
•Vibration felt in the steering wheel
•Potential loss of steering responsiveness
•Uneven tire wear observed

Diagnostic Steps

1
Inspect the front suspension components for wear or damage, including control arms and bushings.
2
Check the CV joints and boots for any signs of damage or lubrication loss.
3
Perform a visual inspection of the wheel bearings for play or roughness.
4
Test drive the vehicle to replicate the noise and determine if it changes with the vehicle's speed or the angle of the turn.
5
Use a stethoscope or listening device to pinpoint the source of the noise while someone turns the steering wheel.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Jack and jack stands
•Socket set
•Torque wrench
•Stethoscope
•Safety glasses

Parts Required

•Control arm bushings (if needed)
•CV joint or axle assembly (if needed)
•Wheel bearings (if needed)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Inspect the front suspension components for wear or damage, including control arms and bushings.
2
Check the CV joints and boots for any signs of damage or lubrication loss.
3
Perform a visual inspection of the wheel bearings for play or roughness.
4
Test drive the vehicle to replicate the noise and determine if it changes with the vehicle's speed or the angle of the turn.
5
Use a stethoscope or listening device to pinpoint the source of the noise while someone turns the steering wheel.

Solution

1. Preparation

Gather tools: jack and jack stands, socket set, torque wrench, stethoscope, and safety glasses.
Ensure the vehicle is parked on a level surface and the engine is off.

2. Lift the Vehicle

Use the jack to lift the front of the vehicle and secure it with jack stands.
Remove the front wheels using a socket set.

3. Inspect Suspension Components

Visually inspect control arms, bushings, and struts for wear or damage.
Check for any loose fasteners and tighten them to specification using a torque wrench.

4. Examine CV Joints

Inspect the CV joint boots for tears or grease leakage.
If the CV joint is damaged, remove the axle nut and disconnect the CV joint from the transmission and hub.

5. Replace Damaged Components

If any components are found to be damaged (e.g., control arms, CV joints), replace them with OEM or high-quality parts.
Reassemble the CV joint or suspension components, ensuring all fasteners are torqued to manufacturer specifications.

6. Reinstall Wheels and Lower Vehicle

Reinstall the front wheels and hand-tighten the lug nuts.
Lower the vehicle from the jack stands and tighten lug nuts to the specified torque.