my Honda Accord 10th Generation (2018-2022) has a check engine light and rough running

Honda Accord 8th Generation (2008-2012)

Error Codes

2-4 hours

Time

medium

Difficulty

high

Severity

3 min read

522 words

⚠️ Safety Warning

This issue requires immediate attention. If you are not experienced with automotive repairs, consult a professional mechanic. Working on critical systems can be dangerous.

Problem Statement

Diagnose and fix rough running and check engine light issues in Honda Accord 10th Generation (2018-2022). Step-by-step guide with diagnostic and repair instructions.

Affected Component

Engine

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect battery before working on electrical systems.
•Allow engine to cool before opening any components.

Symptoms

•Check engine light illuminated
•Rough idle
•Loss of power during acceleration
•Decreased fuel efficiency
•Engine stalling intermittently

Diagnostic Steps

1
Scan for error codes using an OBD-II scanner to identify any stored trouble codes.
2
Inspect the spark plugs for wear or fouling and check ignition coil operation.
3
Examine the air intake system for leaks or blockages.
4
Check the fuel system for pressure using a fuel pressure gauge.
5
Inspect the throttle body for carbon buildup or malfunction.
6
Evaluate the engine coolant temperature sensor for proper operation.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Socket set
•Torque wrench
•Throttle body cleaner
•Fuel pressure gauge

Parts Required

•Spark plugs
•Ignition coils (if necessary)
•Throttle body cleaner
•Engine coolant temperature sensor (if faulty)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Scan for error codes using an OBD-II scanner to identify any stored trouble codes.
2
Inspect the spark plugs for wear or fouling and check ignition coil operation.
3
Examine the air intake system for leaks or blockages.
4
Check the fuel system for pressure using a fuel pressure gauge.
5
Inspect the throttle body for carbon buildup or malfunction.
6
Evaluate the engine coolant temperature sensor for proper operation.

Solution

1. Preparation

Gather tools and parts required for the repair.
Disconnect the battery to ensure safety during repairs.

2. Replace Spark Plugs

Remove the engine cover if necessary.
Use a socket set to remove the spark plug wires or ignition coils.
Use a spark plug socket to remove the old spark plugs.
Inspect the new spark plugs for proper gap size and install them, tightening to manufacturer's torque specifications (typically around 13-15 ft-lbs).
Reconnect the ignition coils or spark plug wires.

3. Clean Throttle Body

Remove the air intake duct connected to the throttle body.
Use throttle body cleaner and a soft cloth to clean the throttle plate and surrounding areas.
Reinstall the air intake duct and secure it properly.

4. Check Fuel System

Connect a fuel pressure gauge to the fuel rail test port.
Turn the ignition to the "ON" position (but do not start the engine) to check the fuel pressure reading. It should be within the manufacturer’s specified range.
If pressure is low, inspect the fuel pump and fuel filter for blockages or failures.

5. Test and Replace Engine Coolant Temperature Sensor (if needed)

Locate the engine coolant temperature sensor on the engine.
Disconnect the electrical connector and remove the sensor using a wrench.
Install the new sensor and reconnect the electrical connector.