how to fix the rear brake noise in my Honda Accord 10th Generation (2018-2022)

Honda Accord 8th Generation (2008-2012)

Error Codes

2-4 hours

Time

medium

Difficulty

medium

Severity

4 min read

660 words

Problem Statement

Learn how to diagnose and fix rear brake noise in Honda Accord 10th Generation (2018-2022). Step-by-step guide with tools and parts required.

Affected Component

Brakes

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Always wear safety goggles and gloves when working on brake systems.
•Ensure the vehicle is securely supported on jack stands before working underneath it.

Symptoms

•Squeaking or squealing noise when braking
•Grinding noise when brakes are applied
•Vibration or pulsation felt through the brake pedal
•Decreased braking efficiency
•Warning light on the dashboard (if equipped with brake wear sensors)

Diagnostic Steps

1
Inspect the rear brake pads for wear and tear using a visual inspection.
2
Check the rear brake rotors for scoring, warping, or damage.
3
Evaluate the brake hardware (caliper, clips, and shims) for proper installation and condition.
4
Inspect for moisture or debris between the brake pad and rotor surfaces.
5
Test the brake fluid level and condition, ensuring it is within the recommended specifications.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Socket set
•Jack
•Jack stands
•Brake pad spreader
•Torque wrench
•Rotor puller (if needed)

Parts Required

•New rear brake pads
•New rear brake rotors (if necessary)
•Brake cleaner (for cleaning components)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Inspect the rear brake pads for wear and tear using a visual inspection.
2
Check the rear brake rotors for scoring, warping, or damage.
3
Evaluate the brake hardware (caliper, clips, and shims) for proper installation and condition.
4
Inspect for moisture or debris between the brake pad and rotor surfaces.
5
Test the brake fluid level and condition, ensuring it is within the recommended specifications.

Solution

1. Preparation

Gather all necessary tools and parts.
Ensure the vehicle is parked on a flat surface and the parking brake is engaged.
Disconnect the negative battery terminal to ensure safety while working on the brakes.

2. Remove Rear Wheel

Tools Required: Socket set, jack, jack stands.
Loosen the lug nuts slightly while the vehicle is on the ground.
Use a jack to raise the rear of the vehicle.
Secure the vehicle on jack stands.
Fully remove the lug nuts and take off the rear wheel.

3. Inspect and Replace Brake Pads

Check the brake pads for thickness. If they are below 3mm, replace them.
Tools Required: Brake pad spreader, socket set.
Remove the caliper bolts using a socket wrench.
Carefully slide the caliper off the rotor. Support it with a bungee cord or similar device to avoid stress on the brake line.
Remove the old brake pads from the caliper bracket.
Install new brake pads into the caliper bracket, ensuring they are properly seated.
Use a brake pad spreader to compress the caliper piston back into the caliper housing.

4. Inspect and Replace Brake Rotors (if necessary)

Tools Required: Torque wrench, rotor puller (if needed).
Check the rotor surface for scoring or damage. If warped or excessively worn, replace the rotor.
Remove the caliper bracket by unbolting it from the hub assembly.
Slide the rotor off the hub. If stuck, gently tap around the rotor with a rubber mallet.
Install the new rotor, ensuring it is clean and free of any oil.
Reattach the caliper bracket and torque to manufacturer specifications.

5. Reassemble and Test

Reinstall the caliper over the new brake pads and torque the caliper bolts to specifications.
Reinstall the rear wheel and torque the lug nuts to the manufacturer’s specifications.
Reconnect the negative battery terminal.
Lower the vehicle back to the ground.
Pump the brake pedal a few times to ensure proper pad seating and restore brake pressure.