how to fix Honda Accord 8th Generation (2008-2012) that shakes during braking

Honda Accord 8th Generation (2008-2012)

Error Codes

2-4 hours

Time

medium

Difficulty

high

Severity

3 min read

496 words

⚠️ Safety Warning

This issue requires immediate attention. If you are not experienced with automotive repairs, consult a professional mechanic. Working on critical systems can be dangerous.

Problem Statement

Learn how to diagnose and fix shaking during braking in Honda Accord 8th Generation (2008-2012). Step-by-step guide with diagnostic procedures and repair instructions.

Affected Component

Brakes

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Always allow the vehicle to cool before working on the brakes.
•Ensure the vehicle is securely supported by jack stands before working underneath.

Symptoms

•Steering wheel shakes or vibrates when braking
•Pulsation felt in the brake pedal
•Vehicle pulls to one side while braking
•Increased stopping distance
•Brake pads or rotors may show uneven wear

Diagnostic Steps

1
Inspect the brake rotors for warping or uneven wear using a dial indicator.
2
Check the brake pads for wear and ensure they have sufficient material left.
3
Examine suspension components, including control arms and bushings, for wear or damage.
4
Check the wheel lug nut torque to ensure they are properly tightened.
5
Test drive the vehicle to confirm if the shaking occurs only during braking.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Torque wrench
•Jack and jack stands
•Socket set
•Brake cleaner
•Micrometer

Parts Required

•Brake rotors
•Brake pads

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Inspect the brake rotors for warping or uneven wear using a dial indicator.
2
Check the brake pads for wear and ensure they have sufficient material left.
3
Examine suspension components, including control arms and bushings, for wear or damage.
4
Check the wheel lug nut torque to ensure they are properly tightened.
5
Test drive the vehicle to confirm if the shaking occurs only during braking.

Solution

1. Preparation

Gather necessary tools and parts.
Park the vehicle on a level surface and engage the parking brake.
Disconnect the battery to ensure safety.

2. Remove Wheel

Use a jack to lift the front or rear wheel (depending on where the issue is) and secure it with jack stands.
Remove the wheel lug nuts using a socket set and take off the wheel.

3. Inspect and Replace Brake Components

Inspect Rotors:
- Measure the rotor thickness with a micrometer; if below specifications, replace them.
- If warped, resurface or replace the rotors.
Inspect Brake Pads:
- Check for uneven wear; replace if necessary.
- Ensure the brake pad shims are in good condition.

4. Reassemble Components

Clean the rotor surface with brake cleaner to remove any contaminants.
Install new or resurfaced rotors, ensuring they are properly seated.
Apply anti-seize lubricant to the hub surface and install the brake pads.
Reinstall the wheel and torque the lug nuts to the manufacturer’s specifications (typically 80-100 ft-lbs).

5. Lower Vehicle and Test

Carefully lower the vehicle and remove jack stands.
Reconnect the battery.
Test the brakes in a safe environment to ensure the issue is resolved.