how to fix Honda Accord 10th Generation (2018-2022) that shakes when braking

Honda Accord 8th Generation (2008-2012)

Error Codes

2-4 hours

Time

medium

Difficulty

high

Severity

3 min read

501 words

⚠️ Safety Warning

This issue requires immediate attention. If you are not experienced with automotive repairs, consult a professional mechanic. Working on critical systems can be dangerous.

Problem Statement

Learn how to diagnose and fix shaking brakes in Honda Accord 10th Generation (2018-2022). Step-by-step guide with symptoms, diagnostic steps, and repair instructions.

Affected Component

Brakes

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Always disconnect the battery before working on electrical systems.
•Allow brakes to cool before working on them to avoid burns.

Symptoms

•Steering wheel shakes when braking
•Vibration felt in the brake pedal
•Uneven brake wear on rotors
•Possible noise from brake components
•Longer stopping distances

Diagnostic Steps

1
Inspect brake rotors for warping or uneven wear using a dial indicator.
2
Check brake pads for uneven wear and proper thickness.
3
Examine suspension components (control arms, bushings, tie rods) for wear or damage.
4
Verify wheel alignment and balance.
5
Scan for any related error codes using an OBD-II scanner.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Jack and jack stands
•Lug wrench
•Socket set
•Brake cleaner
•Torque wrench
•OBD-II scanner
•Dial indicator

Parts Required

•Brake pads
•Brake rotors (if warped)
•Caliper bolts (if damaged)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Inspect brake rotors for warping or uneven wear using a dial indicator.
2
Check brake pads for uneven wear and proper thickness.
3
Examine suspension components (control arms, bushings, tie rods) for wear or damage.
4
Verify wheel alignment and balance.
5
Scan for any related error codes using an OBD-II scanner.

Solution

1. Preparation

Gather necessary tools and parts.
Ensure the vehicle is on a level surface and secure it with wheel chocks.
Disconnect the battery for safety.

2. Remove Wheel

Sub-steps:
1. Loosen the lug nuts slightly while the vehicle is on the ground.
2. Jack up the vehicle and secure it with jack stands.
3. Remove the lug nuts and take off the wheel.

Tools Required:

Jack and jack stands
Lug wrench

3. Inspect and Replace Brake Components

Sub-steps:
1. Remove the caliper bolts using a socket set and carefully lift the caliper off the rotor.
2. Inspect the brake pads for wear; replace if less than 3mm thick.
3. Check the rotor for warping; replace if the runout exceeds manufacturer specifications (typically 0.002 inches).
4. If replacing, clean the hub surface before installing the new rotor.
5. Install new brake pads and reattach the caliper.

Tools Required:

Socket set
Brake cleaner
Torque wrench (for caliper bolts)

4. Reinstall Wheel and Lower Vehicle

Sub-steps:
1. Place the wheel back onto the hub and hand-tighten the lug nuts.
2. Lower the vehicle to the ground.
3. Tighten the lug nuts to the manufacturer's torque specifications (typically 80-100 ft-lbs).

5. Test Drive

Sub-steps:
1. Reconnect the battery if disconnected.
2. Take the vehicle for a test drive to check for vibrations during braking.