how to fix Honda Accord 10th Generation (2018-2022) suspension noise over bumps

Honda Accord 8th Generation (2008-2012)

Error Codes

2-4 hours

Time

medium

Difficulty

medium

Severity

3 min read

456 words

Problem Statement

Learn how to diagnose and fix suspension noise over bumps in Honda Accord 10th Generation (2018-2022). Step-by-step guide with diagnostic procedures and repair instructions.

Affected Component

Suspension

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Always disconnect the battery when working on the suspension system.
•Ensure the vehicle is securely lifted and supported before working underneath.

Symptoms

•Clunking or rattling noise when driving over bumps
•Excessive vibration felt through the steering wheel
•Uneven tire wear
•Vehicle feels unstable on rough roads
•Increased road noise inside the cabin

Diagnostic Steps

1
Inspect the suspension system visually for any obvious signs of damage or wear.
2
Check for loose or damaged components, such as struts, shocks, and bushings.
3
Test the vehicle's ride height to determine if it's within manufacturer specifications.
4
Perform a bounce test by pushing down on each corner of the vehicle to observe how the suspension rebounds.
5
Use a stethoscope to localize the noise while driving over bumps.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Lug wrench
•Jack and jack stands
•Socket set
•Torque wrench
•Pry bar

Parts Required

•Replacement struts/shocks (if damaged)
•Suspension bushings (if worn)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Inspect the suspension system visually for any obvious signs of damage or wear.
2
Check for loose or damaged components, such as struts, shocks, and bushings.
3
Test the vehicle's ride height to determine if it's within manufacturer specifications.
4
Perform a bounce test by pushing down on each corner of the vehicle to observe how the suspension rebounds.
5
Use a stethoscope to localize the noise while driving over bumps.

Solution

1. Preparation

Gather tools and parts.
Ensure the vehicle is parked on a flat surface.
Lift the vehicle using a jack and secure it with jack stands.

2. Inspect and Replace Damaged Components

Remove Wheel
- Use a lug wrench to remove the wheel where the noise is most prominent.
- Tools Required: Lug wrench, jack and jack stands.
Inspect Struts/Shocks
- Check for oil leakage on the struts/shocks indicating failure.
- If damaged, proceed to replace them.
- Tools Required: Socket set, torque wrench.
- Torque Values: Refer to the service manual for specific torque values during reinstallation.
Check Bushings and Mounts
- Inspect all bushings and mounts for signs of wear or cracking.
- Replace any components that show signs of damage.
- Tools Required: Pry bar, socket set.
Reassemble
- Reinstall the wheel and lower the vehicle.
- Tools Required: Torque wrench for lug nuts.
- Ensure lug nuts are torqued to the manufacturer's specifications.

3. Final Check

After replacing components, perform a test drive to verify the noise has been resolved.
Tools Required: None specific, just the vehicle.