how to check if my Honda Accord 10th Generation (2018-2022) wheel bearings are bad?

Honda Accord 8th Generation (2008-2012)

Error Codes

2-4 hours

Time

medium

Difficulty

medium

Severity

3 min read

574 words

Problem Statement

Learn how to check and replace wheel bearings on your Honda Accord 10th Generation (2018-2022). Step-by-step guide with symptoms and diagnostic steps.

Affected Component

Suspension

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Ensure the vehicle is on a flat surface and secure the vehicle on jack stands before working on it.

Symptoms

•Grinding or rumbling noise while driving, especially when turning.
•Vibration in the steering wheel or throughout the vehicle.
•Uneven tire wear.
•Increased road noise that intensifies with speed.
•Looseness or play in the wheel when checked manually.

Diagnostic Steps

1
Check for visible damage or rust on the wheel bearings and surrounding components.
2
Drive the vehicle at different speeds and listen for any abnormal noises that increase with speed.
3
Jack up the vehicle and support it securely on jack stands. Grab the tire at the 12 o'clock and 6 o'clock positions and check for any play in the wheel.
4
Rotate the wheel manually while listening for any grinding noises or roughness.
5
Perform a slow-speed turn while applying the brakes to see if the noise changes or if vibrations occur.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Jack and jack stands
•Lug wrench
•Torque wrench
•Bearing puller

Parts Required

•Replacement wheel bearings
•Brake pads (if worn)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Check for visible damage or rust on the wheel bearings and surrounding components.
2
Drive the vehicle at different speeds and listen for any abnormal noises that increase with speed.
3
Jack up the vehicle and support it securely on jack stands. Grab the tire at the 12 o'clock and 6 o'clock positions and check for any play in the wheel.
4
Rotate the wheel manually while listening for any grinding noises or roughness.
5
Perform a slow-speed turn while applying the brakes to see if the noise changes or if vibrations occur.

Solution

1. Preparation

Gather Tools:
- Jack and jack stands
- Lug wrench
- Torque wrench
- Bearing puller (if replacement is necessary)
Safety Warning: Ensure the vehicle is on a flat surface and secure the vehicle on jack stands before working on it.

2. Remove the Wheel

Loosen the lug nuts using a lug wrench while the vehicle is on the ground.
Jack up the vehicle and secure it with jack stands.
Remove the lug nuts completely and take off the wheel.

3. Inspect the Wheel Bearing

Locate the wheel hub assembly and inspect the exterior for any signs of damage or excessive rust.
Rotate the hub by hand to check for smooth operation. There should be no grinding or roughness.

4. Replace the Wheel Bearing (if necessary)

Remove the Brake Caliper: Unbolt the brake caliper and hang it securely without stressing the brake line.
Remove the Rotor: Unscrew any retaining screws and slide off the brake rotor.
Disconnect the Hub Assembly: Remove the bolts holding the hub assembly in place and disconnect any ABS sensor wiring if applicable.
Use a Bearing Puller: If necessary, use a bearing puller to extract the old bearing from the hub.
Install New Bearing: Press or tap the new bearing into place, ensuring it is seated correctly.

5. Reassemble Components

Reattach the hub assembly, ensuring all bolts are tightened to the manufacturer's torque specifications.
Reinstall the brake rotor and caliper.
Place the wheel back on, hand-tighten the lug nuts, then lower the vehicle and torque the lug nuts to the specified value.