why is there a knocking noise from the engine in my Honda Accord 9th Generation (2013-2017)?

Honda Accord Eleventh Generation (2023-present)

Error Codes

2-4 hours

Time

medium

Difficulty

high

Severity

3 min read

550 words

⚠️ Safety Warning

This issue requires immediate attention. If you are not experienced with automotive repairs, consult a professional mechanic. Working on critical systems can be dangerous.

Problem Statement

Learn how to diagnose and fix engine knocking noise in Honda Accord 9th Generation (2013-2017). Step-by-step guide with diagnostic procedures and repair instructions.

Affected Component

Engine

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on electrical systems.
•Allow the engine to cool down completely before starting repairs.

Symptoms

•Knocking or tapping noise from the engine, especially during acceleration
•Loss of power or acceleration
•Engine misfires or rough idling
•Oil pressure warning light may illuminate
•Increased engine vibration

Diagnostic Steps

1
Scan the vehicle's OBD-II system for any stored error codes.
2
Check the engine oil level and condition; look for signs of contamination or low levels.
3
Inspect the engine mounts for wear or damage that could contribute to noise.
4
Use a stethoscope or mechanic's tool to isolate the source of the knocking noise.
5
Check the timing chain/belt for wear, tension, or misalignment.
6
Inspect the valve train components for wear, including lifters and pushrods.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Oil filter wrench
•Socket set
•Torque wrench
•Mechanic’s stethoscope
•Jack and jack stands

Parts Required

•Engine oil (0W-20 or 5W-20)
•Oil filter
•Valve cover gasket (if applicable)
•Timing chain components (if applicable)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Scan the vehicle's OBD-II system for any stored error codes.
2
Check the engine oil level and condition; look for signs of contamination or low levels.
3
Inspect the engine mounts for wear or damage that could contribute to noise.
4
Use a stethoscope or mechanic's tool to isolate the source of the knocking noise.
5
Check the timing chain/belt for wear, tension, or misalignment.
6
Inspect the valve train components for wear, including lifters and pushrods.

Solution

1. Preparation

Gather tools and parts before starting the repair.
Disconnect the battery to ensure safety.
Ensure the engine is cool before beginning any work.

2. Change Engine Oil and Filter

Sub-steps:
1. Raise the vehicle using a jack and secure it with jack stands.
2. Remove the oil drain plug and drain the old oil into a container.
3. Replace the oil filter using an oil filter wrench; lubricate the new filter's gasket with new oil before installation.
4. Reinstall the drain plug and torque it to the manufacturer's specifications (typically around 30 ft-lbs).
5. Fill the engine with the recommended oil type (usually 0W-20 or 5W-20) and check the oil level with the dipstick.

3. Inspect and Replace Worn Components

Sub-steps:
1. If knocking persists, remove the valve cover to access the valve train.
2. Inspect the rocker arms and lifters for wear.
3. Replace any worn lifters or rocker arms as necessary.
4. Reassemble the valve cover using a new gasket to prevent oil leaks.

4. Timing Chain/Belt Inspection

Sub-steps:
1. If a timing chain is suspected, remove the timing cover for inspection.
2. Check the chain tensioner for proper function and wear.
3. If the timing chain is stretched, replace it along with the tensioner and guides.
4. Reassemble the timing cover and ensure all components are secured.