why does my Honda Accord 9th Generation (2013-2017) make squeaking noises when I brake

Honda Accord Eleventh Generation (2023-present)

Error Codes

2-4 hours

Time

medium

Difficulty

medium

Severity

3 min read

573 words

Problem Statement

Learn how to diagnose and fix squeaking noises when braking in Honda Accord 9th Generation (2013-2017). Step-by-step guide with diagnostic procedures and repair instructions.

Affected Component

Brakes

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Always disconnect the battery before working on the brake system to prevent electrical issues.
•Allow the brakes to cool before starting any work to avoid burns.

Symptoms

•Squeaking or squealing noise when brakes are applied
•Reduced braking efficiency
•Vibration in the brake pedal
•Brake warning light illuminated (if applicable)
•Dust accumulation on brake components

Diagnostic Steps

1
Inspect brake pads for wear and uneven surfaces using a visual inspection.
2
Check brake rotors for scoring, warping, or rust buildup.
3
Examine brake calipers for proper operation and any signs of sticking.
4
Inspect brake hardware (shims, clips) to ensure they are intact and properly lubricated.
5
Verify brake fluid level and condition in the master cylinder reservoir.
6
Perform a road test to confirm the conditions under which the noise occurs.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Jack and jack stands
•Lug wrench
•Socket set
•Torque wrench
•Brake cleaner
•Lubricant (high-temperature brake grease)

Parts Required

•Brake pads
•Brake rotors (if needed)
•Brake cleaner
•High-temperature brake grease

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Inspect brake pads for wear and uneven surfaces using a visual inspection.
2
Check brake rotors for scoring, warping, or rust buildup.
3
Examine brake calipers for proper operation and any signs of sticking.
4
Inspect brake hardware (shims, clips) to ensure they are intact and properly lubricated.
5
Verify brake fluid level and condition in the master cylinder reservoir.
6
Perform a road test to confirm the conditions under which the noise occurs.

Solution

1. Preparation

Gather tools and materials.
Park the vehicle on a flat surface and engage the parking brake.
Wear safety glasses and gloves.

Tools Required:

Jack and jack stands
Lug wrench
Socket set
Torque wrench
Brake cleaner
Lubricant (high-temperature brake grease)

2. Remove Wheel

Loosen the lug nuts slightly while the vehicle is on the ground.
Raise the vehicle using a jack and secure it with jack stands.
Remove the lug nuts completely and take off the wheel.

3. Inspect and Replace Brake Pads

Visually inspect the brake pads for thickness; replace if less than 3mm.
If replacement is needed:
- Remove the caliper bolts using a socket wrench.
- Slide the caliper off the brake rotor and secure it with a bungee cord to avoid stressing the brake line.
- Remove the old brake pads from the caliper bracket.
- Clean the caliper bracket and rotor with brake cleaner.
- Install new brake pads, ensuring proper orientation and alignment.
- Apply high-temperature brake grease to the back of the pads and any contact points.

4. Inspect and Resurface or Replace Rotors

Check the rotors for any scoring or warping; if warped, consider resurfacing or replacing.
If replacing, remove the caliper bracket and rotor from the hub.
Install the new or resurfaced rotor and reattach the caliper bracket.

5. Reassemble and Torque

Reinstall the caliper over the new pads.
Tighten caliper bolts to manufacturer-recommended torque specifications (typically around 20-25 ft-lbs).
Reinstall the wheel and tighten lug nuts in a crisscross pattern to ensure even seating.

6. Final Checks

Lower the vehicle and recheck lug nut torque after the first drive.
Pump the brake pedal to seat the pads against the rotor.