why does my Honda Accord 9th Generation (2013-2017) make a squeaking noise when I brake

Honda Accord Eleventh Generation (2023-present)

Error Codes

2-4 hours

Time

medium

Difficulty

medium

Severity

3 min read

506 words

Problem Statement

Learn how to diagnose and fix squeaking noise when braking in Honda Accord 9th Generation (2013-2017). Step-by-step guide with diagnostic procedures and repair instructions.

Affected Component

Brakes

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Always engage the parking brake and use jack stands when working under the vehicle.

Symptoms

•Squeaking noise when applying brakes
•Decreased braking efficiency
•Vibration in the brake pedal
•Brake warning light illuminated
•Increased stopping distance

Diagnostic Steps

1
Inspect brake pads for wear and tear using a visual inspection.
2
Check brake rotor surface for scoring or uneven wear.
3
Examine the brake calipers for proper operation and any signs of sticking.
4
Inspect brake fluid level and condition in the reservoir.
5
Test-drive the vehicle to replicate the noise under various braking conditions.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Lug wrench
•Jack
•Jack stands
•Socket set
•Torque wrench
•Brake cleaner
•C-clamp

Parts Required

•Brake pads
•Brake rotors

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Inspect brake pads for wear and tear using a visual inspection.
2
Check brake rotor surface for scoring or uneven wear.
3
Examine the brake calipers for proper operation and any signs of sticking.
4
Inspect brake fluid level and condition in the reservoir.
5
Test-drive the vehicle to replicate the noise under various braking conditions.

Solution

1. Preparation

Gather tools and parts needed for brake inspection and replacement.
Ensure the vehicle is parked on a level surface and the parking brake is engaged.

2. Remove Wheel

Tools Required: Lug wrench, jack, jack stands
Sub-steps:
1. Loosen the lug nuts slightly while the wheel is on the ground.
2. Lift the vehicle using the jack and secure it with jack stands.
3. Remove the lug nuts completely and take off the wheel.

3. Inspect Brake Components

Tools Required: Brake cleaner, torque wrench
Sub-steps:
1. Clean the brake components with brake cleaner to remove dust and debris.
2. Inspect brake pads for thickness; replace if less than 3mm.
3. Check brake rotors for grooves or warping; replace if necessary.
4. Ensure brake caliper slides freely and is not sticking.

4. Replace Brake Pads (if necessary)

Tools Required: Socket set, C-clamp (for caliper piston retraction), grease
Sub-steps:
1. Remove caliper bolts and lift the caliper away from the rotor.
2. Use a C-clamp to retract the caliper piston.
3. Remove old brake pads and install new pads, applying a thin layer of grease to the backing.
4. Reinstall the caliper and tighten bolts to manufacturer specifications (typically around 25-30 lb-ft).

5. Reassemble and Test

Tools Required: Lug wrench, torque wrench
Sub-steps:
1. Reinstall the wheel and hand-tighten the lug nuts.
2. Lower the vehicle and torque the lug nuts to manufacturer specifications (typically 80-100 lb-ft).
3. Test the brakes by pressing the pedal several times before driving.