why does my Honda Accord 9th Generation (2013-2017) make a popping noise when turning

Honda Accord Eleventh Generation (2023-present)

Error Codes

2-4 hours

Time

medium

Difficulty

medium

Severity

3 min read

522 words

Problem Statement

Learn how to diagnose and fix popping noise when turning in Honda Accord 9th Generation. Step-by-step guide with diagnostic procedures and repair instructions.

Affected Component

Suspension

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Always ensure the vehicle is securely supported on jack stands before working underneath.
•Wear safety glasses to protect your eyes from debris.

Symptoms

•Popping noise when turning the steering wheel
•Noise may vary in intensity based on turning radius
•Possible vibration felt through the steering wheel
•Clunking noise over bumps
•Uneven tire wear on the front tires

Diagnostic Steps

1
Inspect the CV joints for any signs of wear or damage.
2
Examine the suspension components, including bushings and struts, for any signs of play or damage.
3
Check the steering linkage for loose or damaged parts.
4
Perform a visual inspection of the wheel bearings for signs of wear or noise.
5
Test drive the vehicle to replicate the noise and observe any additional symptoms.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Socket set
•Torque wrench
•Pry bar
•Ball joint separator
•Steering wheel puller

Parts Required

•CV joint assembly
•Control arms or bushings (if needed)
•Tie rod ends (if needed)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Inspect the CV joints for any signs of wear or damage.
2
Examine the suspension components, including bushings and struts, for any signs of play or damage.
3
Check the steering linkage for loose or damaged parts.
4
Perform a visual inspection of the wheel bearings for signs of wear or noise.
5
Test drive the vehicle to replicate the noise and observe any additional symptoms.

Solution

1. Preparation

Gather necessary tools and parts.
Park the vehicle on a level surface and engage the parking brake.
Place the vehicle on jack stands to safely elevate the front end.

2. Inspect and Replace CV Joints

Tools Required: Socket set, torque wrench, pry bar, CV joint grease
Remove the wheel on the affected side using a socket set.
Inspect the CV boot for tears or leaks. If damaged, replace the CV joint assembly.
To replace, remove the axle nut with a socket and pull the axle out of the hub.
Install the new CV joint, ensuring to fill it with grease, and reassemble the axle nut to the manufacturer's torque specifications.

3. Check and Replace Suspension Components

Tools Required: Socket set, torque wrench, jack, ball joint separator
Inspect control arms, bushings, and struts for damage.
If any components are worn or damaged, remove them using the appropriate tools.
Replace with new OEM or quality aftermarket parts, ensuring all bolts are torqued to specifications.

4. Inspect and Replace Steering Linkage

Tools Required: Socket set, torque wrench, steering wheel puller if necessary
Check the tie rod ends for play by moving them while the vehicle is elevated.
If play is detected, remove the nut securing the tie rod end and use a steering wheel puller if needed.
Replace with a new tie rod end and torque the nut to the specified value.