why does my Honda Accord 9th Generation (2013-2017) make a grinding noise when turning

Honda Accord Eleventh Generation (2023-present)

Error Codes

2-4 hours

Time

medium

Difficulty

medium

Severity

3 min read

515 words

Problem Statement

Learn how to diagnose and fix grinding noise when turning in Honda Accord 9th Generation. Step-by-step guide with symptoms, diagnostic steps, and repair instructions.

Affected Component

Steering

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect battery before working on electrical systems.
•Use jack stands to secure the vehicle when working underneath.

Symptoms

•Grinding noise during turns
•Decreased steering responsiveness
•Vibration in the steering wheel
•Clunking or popping noise associated with steering movement
•Uneven tire wear

Diagnostic Steps

1
Inspect the power steering fluid level and condition.
2
Check for any visible damage to the CV joints or axles.
3
Examine the brake components for wear or misalignment.
4
Inspect suspension components such as struts and control arms for damage.
5
Test drive the vehicle to confirm the conditions under which the noise occurs.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Socket set
•Torque wrench
•Brake caliper tool
•Funnel
•Clean rags
•Pry bar

Parts Required

•Power steering fluid
•CV joint/axle assembly (if needed)
•Brake pads (if needed)
•Brake rotors (if needed)
•Suspension components (if needed)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Inspect the power steering fluid level and condition.
2
Check for any visible damage to the CV joints or axles.
3
Examine the brake components for wear or misalignment.
4
Inspect suspension components such as struts and control arms for damage.
5
Test drive the vehicle to confirm the conditions under which the noise occurs.

Solution

1. Preparation

Gather necessary tools and parts.
Park the vehicle on a level surface and engage the parking brake.
Disconnect the battery if working on electrical components.

2. Inspect and Replace Power Steering Fluid

Sub-steps:
1. Locate the power steering fluid reservoir.
2. Check the fluid level and condition; if low or contaminated, drain the old fluid.
3. Refill with the manufacturer-recommended power steering fluid.
Tools Required: Funnel, clean rags.

3. Check and Replace CV Joints/Axles

Sub-steps:
1. Lift the front of the vehicle and secure it with jack stands.
2. Inspect the CV boots for tears or leaks; replace if damaged.
3. If the CV joint is worn, remove the axle nut and disconnect the axle from the hub.
4. Install a new axle or CV joint as necessary, ensuring proper torque specifications are followed (typically 130-150 ft-lbs for axle nut).
Tools Required: Socket set, torque wrench, pry bar.

4. Inspect and Replace Brake Components

Sub-steps:
1. Remove the wheel to access the brake assembly.
2. Inspect brake pads for wear; replace if worn below specifications (typically 3mm).
3. Check the rotor for grooves or warping; replace if necessary.
Tools Required: Brake caliper tool, socket set.

5. Examine and Repair Suspension Components

Sub-steps:
1. Inspect control arms, struts, and sway bar links for damage or wear.
2. Replace any worn components with OEM or quality aftermarket parts.
3. Ensure all bolts are torqued to the manufacturer specifications.
Tools Required: Socket set, torque wrench, penetrating oil.