why does my Honda Accord 9th Generation (2013-2017) make a grinding noise when braking

Honda Accord Eleventh Generation (2023-present)

Error Codes

2-4 hours

Time

medium

Difficulty

high

Severity

3 min read

523 words

⚠️ Safety Warning

This issue requires immediate attention. If you are not experienced with automotive repairs, consult a professional mechanic. Working on critical systems can be dangerous.

Problem Statement

Discover the causes and solutions for grinding noise when braking in Honda Accord 9th Generation. Step-by-step guide for effective brake repair.

Affected Component

Brakes

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Always allow the brakes to cool before working on them.
•Wear safety glasses and gloves when handling brake components.

Symptoms

•Grinding noise when applying brakes
•Vibration felt through the brake pedal
•Reduced braking efficiency
•Squeaking or squealing sounds prior to grinding
•Warning light for brake system illuminated

Diagnostic Steps

1
Inspect the brake pads for wear and thickness using a visual inspection.
2
Check the brake rotors for scoring, warping, or damage.
3
Examine brake calipers for proper operation and any sign of sticking.
4
Inspect brake fluid levels and condition.
5
Listen for noise when the vehicle is stationary and the brake pedal is pressed.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Jack and jack stands
•Socket set
•Torque wrench
•Brake grease
•Screwdriver

Parts Required

•Brake pads
•Brake rotors (if needed)
•Brake fluid (if necessary)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Inspect the brake pads for wear and thickness using a visual inspection.
2
Check the brake rotors for scoring, warping, or damage.
3
Examine brake calipers for proper operation and any sign of sticking.
4
Inspect brake fluid levels and condition.
5
Listen for noise when the vehicle is stationary and the brake pedal is pressed.

Solution

1. Preparation

Gather all necessary tools and parts.
Park the vehicle on a flat surface and engage the parking brake.
Disconnect the battery to ensure safety during repairs.

2. Remove Wheel

Use a jack to lift the vehicle and securely place it on jack stands.
Remove the lug nuts with a socket wrench and take off the wheel.

3. Inspect and Replace Brake Pads

Inspect Brake Pads:
- Check the thickness of the pads; if they are less than 3mm, they should be replaced.
Remove Old Brake Pads:
- Unbolt the caliper using a socket wrench and slide it off the rotor.
- Remove the old brake pads from the caliper bracket.
Install New Brake Pads:
- Apply brake grease to the backing plates of the new pads.
- Slide the new pads into the caliper bracket.

4. Inspect and Replace Brake Rotors (if necessary)

Inspect Rotors:
- Check for grooves or warping; if they are damaged, they should be replaced.
Remove Old Rotor:
- Unbolt the rotor from the hub (if applicable) and slide it off.
Install New Rotor:
- Place the new rotor onto the hub and secure it with bolts.

5. Reassemble and Test

Reattach the brake caliper over the new pads and torque the bolts to manufacturer specifications (usually around 25-35 ft-lbs).
Reinstall the wheel and lug nuts, and torque them to the manufacturer’s specification (typically 80-100 ft-lbs).
Lower the vehicle and reconnect the battery.