why does my Honda Accord 9th Generation (2013-2017) make a clicking noise when turning

Honda Accord Eleventh Generation (2023-present)

Error Codes

2-4 hours

Time

medium

Difficulty

medium

Severity

3 min read

597 words

Problem Statement

Learn how to diagnose and fix clicking noise when turning in Honda Accord 9th Generation. Step-by-step guide with diagnostic procedures and repair instructions.

Affected Component

Suspension

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Always disconnect the battery before working on electrical components.
•Allow the vehicle to cool before working on any hot engine components.

Symptoms

•Clicking noise during left or right turns
•Noise intensifies with sharper turns
•Vibration felt in the steering wheel
•Possible loss of power steering assistance
•Unusual tire wear patterns (if observed)

Diagnostic Steps

1
Inspect the CV joints for any visible damage or wear.
2
Check for play in the wheel bearings by jacking up the vehicle and shaking the wheel.
3
Examine the power steering fluid level and condition.
4
Test drive the vehicle to isolate the noise and determine if it occurs under specific conditions (e.g., speed, turning radius).
5
Inspect the suspension components (e.g., control arms, tie rods) for any signs of wear or damage.
6
Listen for noise changes when accelerating or decelerating while turning.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Jack
•Jack stands
•Socket set
•Torque wrench
•Bearing puller

Parts Required

•CV joint (if damaged)
•Wheel bearings (if worn)
•Power steering fluid (if low)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Inspect the CV joints for any visible damage or wear.
2
Check for play in the wheel bearings by jacking up the vehicle and shaking the wheel.
3
Examine the power steering fluid level and condition.
4
Test drive the vehicle to isolate the noise and determine if it occurs under specific conditions (e.g., speed, turning radius).
5
Inspect the suspension components (e.g., control arms, tie rods) for any signs of wear or damage.
6
Listen for noise changes when accelerating or decelerating while turning.

Solution

1. Preparation

Gather tools: jack, jack stands, socket set, torque wrench, and safety goggles.
Ensure the vehicle is on a flat surface and safely secured with the parking brake engaged.

2. Inspect and Replace CV Joints

Inspect CV Joints:
- Remove the wheel cover (if equipped) and tire to access the CV axle.
- Check the CV joint boot for tears or grease leakage.
Replace CV Joint (if necessary):
- Remove the axle nut using a socket.
- Detach the CV axle from the hub assembly using a puller if necessary.
- Install the new CV joint by reversing the removal steps and ensuring the boot is properly seated.
- Torque the axle nut to the manufacturer's specifications (typically 100-140 ft-lbs).

3. Check and Replace Wheel Bearings

Inspect Wheel Bearings:
- With the wheel off, shake the hub assembly to check for excessive play.
Replace Wheel Bearing (if necessary):
- Remove the brake caliper and rotor.
- Use a bearing puller to extract the old wheel bearing.
- Press or install the new bearing into the hub assembly, ensuring it is seated correctly.
- Reassemble the brake components and wheel, torquing all bolts to specifications.

4. Inspect and Top Off Power Steering Fluid

Check Fluid Level:
- Locate the power steering reservoir and check the fluid level against the dipstick or markings.
Top Off:
- If low, add the manufacturer-recommended power steering fluid until it reaches the proper level.

5. Inspect Suspension Components

Visual Inspection:
- Check control arms, tie rods, and bushings for deterioration or cracking.
Replace Components (if necessary):
- Remove the affected suspension components using the appropriate tools.
- Install new components, ensuring all bolts are torqued to the manufacturer's specifications.