my Honda Accord 9th Generation (2013-2017) won't start and just clicks what's the problem

Honda Accord Eleventh Generation (2023-present)

Error Codes

1-3 hours

Time

medium

Difficulty

high

Severity

3 min read

478 words

⚠️ Safety Warning

This issue requires immediate attention. If you are not experienced with automotive repairs, consult a professional mechanic. Working on critical systems can be dangerous.

Problem Statement

Learn how to diagnose and fix the no-start issue in Honda Accord 9th Generation (2013-2017). Step-by-step guide with symptoms and solutions.

Affected Component

Electrical

Estimated Time

1-3 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on electrical systems.
•Wear gloves and safety glasses while handling the battery and starter motor.

Symptoms

•Clicking noise when the ignition key is turned
•Dashboard lights illuminate but engine does not crank
•Possible dimming of dashboard lights during the clicking
•Battery warning light may be illuminated
•No sound from the starter motor

Diagnostic Steps

1
Check the battery voltage using a multimeter to ensure it is above 12.4 volts.
2
Inspect battery terminals for corrosion or loose connections.
3
Attempt to jump-start the vehicle with jumper cables and a functioning vehicle.
4
Check the fuses related to the starter system for any blown fuses.
5
Test the starter relay by swapping it with a similar relay from another system in the fuse box.
6
Inspect the wiring to the starter motor for damage or loose connections.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Multimeter
•Socket set
•Jumper cables
•Wire brush

Parts Required

•Replacement battery
•Starter motor

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Check the battery voltage using a multimeter to ensure it is above 12.4 volts.
2
Inspect battery terminals for corrosion or loose connections.
3
Attempt to jump-start the vehicle with jumper cables and a functioning vehicle.
4
Check the fuses related to the starter system for any blown fuses.
5
Test the starter relay by swapping it with a similar relay from another system in the fuse box.
6
Inspect the wiring to the starter motor for damage or loose connections.

Solution

1. Preparation

Gather tools: socket set, multimeter, jumper cables, and a replacement battery (if needed).
Ensure the vehicle is in park and the ignition is off.

2. Battery Inspection

Disconnect the battery terminals, starting with the negative terminal to avoid a short circuit.
Clean any corrosion from the battery terminals using a wire brush and a mixture of baking soda and water.
Reconnect the terminals, ensuring they are tight; connect the positive terminal first, followed by the negative terminal.

3. Battery Replacement (if necessary)

Remove the old battery by unbolting any securing brackets and lifting it out.
Install the new battery, ensuring it is positioned correctly.
Reconnect the positive terminal first, followed by the negative terminal, and secure the battery in place.

4. Starter Motor Inspection

Locate the starter motor (usually found near the engine's transmission).
Check the wiring to the starter motor for any signs of wear or loose connections.
If wiring is intact, test the starter motor by applying direct voltage from the battery using jumper cables (ensure safety precautions).
If the starter motor does not engage, it may need replacement.