my Honda Accord 9th Generation (2013-2017) remote start not working how to fix

Honda Accord Eleventh Generation (2023-present)

Error Codes

1-2 hours

Time

medium

Difficulty

medium

Severity

3 min read

528 words

Problem Statement

Learn how to diagnose and fix the remote start issue in Honda Accord 9th Generation (2013-2017). Step-by-step guide with tools and tips.

Affected Component

Electrical

Estimated Time

1-2 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Always disconnect the battery before working on electrical components to avoid shorts.

Symptoms

•Remote start button does not respond when pressed
•Key fob battery is dead or weak
•Engine does not start or turn over when attempted remotely
•Security or immobilizer warning light is illuminated
•Check engine light may be illuminated

Diagnostic Steps

1
Check the key fob battery by testing or replacing it to ensure proper function.
2
Scan for error codes using an OBD-II scanner to identify any underlying issues.
3
Verify that the vehicle is in the correct condition for remote start (e.g., doors closed, hood closed, and no active security system).
4
Inspect the key fob for physical damage or wear.
5
Check the vehicle's battery voltage and ensure it is within operational range.
6
Test the remote start system with a second key fob if available, to rule out a faulty fob.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Multimeter
•Small flathead screwdriver

Parts Required

•Coin cell battery (CR2032)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Check the key fob battery by testing or replacing it to ensure proper function.
2
Scan for error codes using an OBD-II scanner to identify any underlying issues.
3
Verify that the vehicle is in the correct condition for remote start (e.g., doors closed, hood closed, and no active security system).
4
Inspect the key fob for physical damage or wear.
5
Check the vehicle's battery voltage and ensure it is within operational range.
6
Test the remote start system with a second key fob if available, to rule out a faulty fob.

Solution

1. Preparation

Gather tools and parts.
Ensure the vehicle is parked safely with the engine off.
Disconnect the negative terminal of the battery to prevent electrical shorts.

2. Replace Key Fob Battery

Tools Required: Small flathead screwdriver, replacement coin cell battery (CR2032).
Sub-steps:
1. Use the flathead screwdriver to gently pry open the key fob.
2. Remove the old battery and replace it with the new CR2032 battery, ensuring correct polarity.
3. Reassemble the key fob and test the remote start function.

3. Check Vehicle Battery Voltage

Tools Required: Multimeter.
Sub-steps:
1. Reconnect the negative terminal of the battery.
2. Set the multimeter to DC voltage and connect the leads to the battery terminals.
3. Ensure the voltage is above 12.4 volts. If below, charge or replace the battery.

4. Inspect Remote Start System

Tools Required: OBD-II scanner.
Sub-steps:
1. Reconnect the negative battery terminal if it was disconnected.
2. Use the OBD-II scanner to check for any trouble codes related to the remote start system.
3. Address any identified issues based on the error codes.

5. Verify Conditions for Remote Start

Sub-steps:
1. Ensure all doors are closed, and the hood is securely shut.
2. Confirm that the vehicle is in park (automatic transmission) or neutral (manual transmission).
3. Check that there are no active security alerts on the dashboard.