my Honda Accord 9th Generation (2013-2017) is making a strange noise when turning, what should I che...

Honda Accord Eleventh Generation (2023-present)

Error Codes

2-4 hours

Time

medium

Difficulty

medium

Severity

3 min read

595 words

Problem Statement

Learn how to diagnose and fix strange noise when turning in Honda Accord 9th Generation. Step-by-step guide with diagnostic procedures and repair instructions.

Affected Component

Steering

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Ensure the vehicle is securely lifted and supported before working underneath.
•Disconnect the battery before performing any electrical work.

Symptoms

•Unusual grinding or clicking noise when turning the steering wheel
•Difficulty steering or a feeling of resistance when turning
•Vibration in the steering wheel during turns
•Noise increases with speed during turns
•Uneven tire wear visible

Diagnostic Steps

1
Inspect the power steering fluid level and condition.
2
Check for any visible leaks around the power steering system.
3
Listen for noise while turning the steering wheel with the vehicle stationary (check for play in components).
4
Examine the CV joints and boots for damage or wear.
5
Inspect the wheel bearings for signs of wear or damage.
6
Check the suspension components, including struts and control arms, for any signs of damage or looseness.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Socket set
•Torque wrench
•Siphon pump
•Jack and jack stands
•Screwdrivers

Parts Required

•Honda Power Steering Fluid
•CV joint assembly (if needed)
•Wheel bearings (if needed)
•Suspension components (if needed)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Inspect the power steering fluid level and condition.
2
Check for any visible leaks around the power steering system.
3
Listen for noise while turning the steering wheel with the vehicle stationary (check for play in components).
4
Examine the CV joints and boots for damage or wear.
5
Inspect the wheel bearings for signs of wear or damage.
6
Check the suspension components, including struts and control arms, for any signs of damage or looseness.

Solution

1. Preparation

Gather necessary tools and parts.
Park the vehicle on a flat surface and secure it with wheel chocks.
Disconnect the negative battery terminal to ensure safety.

2. Inspect and Replace Power Steering Fluid

Locate the power steering fluid reservoir.
Remove the cap and check the fluid level; top off if low with the recommended fluid type (Honda Power Steering Fluid).
If the fluid appears dirty, drain and replace it.
- Use a siphon pump to remove old fluid.
- Refill with fresh fluid.

3. Check and Replace CV Joints (if damaged)

Lift the front end of the vehicle and secure it on jack stands.
Remove the wheel to access the CV joint.
Inspect the CV boot for tears; if damaged, replace the CV joint.
- Remove the axle nut using a socket.
- Disconnect the lower control arm if necessary.
- Slide out the axle and replace it with a new CV joint assembly.
- Reinstall in reverse order and torque the axle nut to the manufacturer’s specifications (typically around 150 ft-lbs).

4. Inspect and Replace Wheel Bearings (if worn)

With the vehicle still lifted, check for play in the wheel by rocking it at 12 and 6 o'clock positions.
If play is detected, remove the wheel and brake caliper.
Remove the hub assembly to gain access to the wheel bearings.
Replace any worn bearings with new ones and reassemble.
- Torque the hub nut to the specified value (commonly around 85 ft-lbs).

5. Inspect and Replace Suspension Components (if necessary)

Check struts and control arms for wear or damage.
Replace any defective components with OEM parts.
Ensure proper alignment after replacing any suspension parts.