my Honda Accord 9th Generation (2013-2017) is making a clicking noise, what does that mean?

Honda Accord Eleventh Generation (2023-present)

Error Codes

2-4 hours

Time

medium

Difficulty

medium

Severity

3 min read

528 words

Problem Statement

Learn how to diagnose and fix clicking noise issues in Honda Accord 9th Generation (2013-2017). Step-by-step guide with diagnostic procedures and repair instructions.

Affected Component

Suspension

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Ensure the vehicle is securely elevated on jack stands before working underneath.
•Disconnect the battery if working with electrical components related to the ABS system.

Symptoms

•Clicking noise when turning the steering wheel
•Clicking sound during acceleration
•Noise that occurs at low speeds
•Vibration felt through the steering wheel
•No warning lights on the dashboard

Diagnostic Steps

1
Inspect the CV joints for signs of wear or damage.
2
Check the wheel bearings for play or unusual wear.
3
Examine the suspension components for loose or damaged parts.
4
Listen for the location of the clicking noise to determine if it is coming from the front or rear of the vehicle.
5
Test drive the vehicle to replicate the noise under various conditions (turning, accelerating).

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Socket set
•Torque wrench
•Pry bar
•CV joint boot clamp tool
•Bearing puller
•Wrench set
•Flashlight

Parts Required

•CV joint assembly (if necessary)
•Wheel bearing (if necessary)
•Suspension components (if necessary)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Inspect the CV joints for signs of wear or damage.
2
Check the wheel bearings for play or unusual wear.
3
Examine the suspension components for loose or damaged parts.
4
Listen for the location of the clicking noise to determine if it is coming from the front or rear of the vehicle.
5
Test drive the vehicle to replicate the noise under various conditions (turning, accelerating).

Solution

1. Preparation

Gather tools and parts required for the repair.
Park the vehicle on a level surface and engage the parking brake.
Use jack stands to elevate the front of the vehicle safely.

2. Inspect and Replace CV Joints

Tools Required: Socket set, torque wrench, pry bar, CV joint boot clamp tool.
Remove the wheel on the side where the clicking noise is prevalent.
Inspect the CV joint for torn boots or grease leaks.
If damaged, remove the axle nut and detach the CV joint from the transmission.
Replace the CV joint with a new one, ensuring proper grease is applied and boots are secured with clamps.
Reinstall the wheel and torque the axle nut to the manufacturer’s specifications.

3. Check and Replace Wheel Bearings (if necessary)

Tools Required: Bearing puller, socket set, torque wrench.
After removing the wheel, check for play by grabbing the tire at 12 and 6 o’clock positions.
If play is detected, remove the brake caliper and rotor to access the wheel bearing.
Use a bearing puller to extract the old bearing and install a new one.
Reassemble the brake components and wheel, torquing to specifications.

4. Inspect Suspension Components

Tools Required: Wrench set, flashlight.
Visually inspect control arms, tie rods, and bushings for wear or damage.
If any components are worn, replace them with OEM parts.
Tighten all bolts to the recommended torque values.