my Honda Accord 9th Generation (2013-2017) has a clicking noise when I turn the steering wheel

Honda Accord Eleventh Generation (2023-present)

Error Codes

2-4 hours

Time

medium

Difficulty

medium

Severity

3 min read

561 words

Problem Statement

Learn how to diagnose and fix clicking noise in steering of Honda Accord 9th Generation. Step-by-step guide with diagnostic procedures and repair instructions.

Affected Component

Steering

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Always use jack stands when working under the vehicle.
•Ensure the engine is off and the keys are removed from the ignition before beginning work.

Symptoms

•Clicking noise when turning the steering wheel
•Difficulty in steering or stiffness in the steering response
•Vibration felt through the steering wheel
•Uneven tire wear
•Steering wheel misalignment

Diagnostic Steps

1
Inspect the power steering fluid level and condition.
2
Check for any visible wear or damage in the CV joints and boots.
3
Test drive the vehicle while making sharp turns to replicate the noise.
4
Inspect the tie rod ends and ball joints for wear or damage.
5
Examine the steering column for any loose components or bushings.
6
Check the wheel bearings for play or noise during rotation.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Socket set
•Torque wrench
•Pry bar
•CV joint removal tool
•Tie rod end puller
•Wrench set

Parts Required

•New CV joint
•New tie rod ends (if necessary)
•Power steering fluid (if low)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Inspect the power steering fluid level and condition.
2
Check for any visible wear or damage in the CV joints and boots.
3
Test drive the vehicle while making sharp turns to replicate the noise.
4
Inspect the tie rod ends and ball joints for wear or damage.
5
Examine the steering column for any loose components or bushings.
6
Check the wheel bearings for play or noise during rotation.

Solution

1. Preparation

Gather tools and parts needed for the repair.
Ensure the vehicle is parked on a flat surface and the ignition is off.
Disconnect the battery to prevent any electrical issues during repair.

2. Inspect and Replace CV Joints

Tools Required: Socket set, torque wrench, pry bar, CV joint removal tool.
Sub-steps:
1. Lift the front of the vehicle using a jack and secure it with jack stands.
2. Remove the front wheel to access the CV joint.
3. Inspect the CV joint boot for tears or grease leakage; replace if necessary.
4. If the CV joint is damaged, use the CV joint removal tool to detach it from the axle.
5. Install the new CV joint by reversing the removal steps and torque the axle nut to the manufacturer's specifications (typically around 150 ft-lbs).

3. Inspect and Replace Tie Rod Ends (if necessary)

Tools Required: Socket set, tie rod end puller, torque wrench.
Sub-steps:
1. After inspecting the tie rod ends, if play is detected, proceed to replace them.
2. Use a tie rod end puller to detach the tie rod end from the steering knuckle.
3. Thread off the old tie rod and install the new one, making sure to adjust to the same length as the old one for alignment purposes.
4. Torque the tie rod nut to the specified value (usually around 45 ft-lbs).

4. Reassemble and Test

Tools Required: Wrench set, torque wrench.
Sub-steps:
1. Reattach the wheel and lower the vehicle.
2. Reconnect the battery.
3. Test drive the vehicle to ensure that the clicking noise is resolved.