my Honda Accord 9th Generation (2013-2017) AC just stopped blowing cold air what happened

Honda Accord Eleventh Generation (2023-present)

Error Codes

2-4 hours

Time

medium

Difficulty

medium

Severity

4 min read

613 words

Problem Statement

Learn how to diagnose and fix AC not blowing cold air in Honda Accord 9th Generation. Step-by-step guide with symptoms, diagnostic steps, and repair instructions.

Affected Component

HVAC

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect battery before working on electrical systems.
•Allow the engine to cool before working on the AC components.
•Handle refrigerants with care and follow environmental regulations when disposing of old refrigerant.

Symptoms

•AC compressor not engaging
•Warm air blowing from vents
•Unusual noises from the AC compressor
•AC system blowing air but not at a cold temperature
•Dashboard warning lights illuminated
•Reduced airflow from the AC vents

Diagnostic Steps

1
Scan for error codes using an OBD-II scanner to check for any AC system-related faults.
2
Inspect the AC refrigerant level using a manifold gauge set to determine if it is low or empty.
3
Check the AC compressor for any signs of damage or wear, including electrical connections and the clutch operation.
4
Inspect the cabin air filter for clogs that may restrict airflow.
5
Verify the operation of the AC relay and fuses related to the AC system.
6
Test the temperature of the air coming from the vents with a thermometer to confirm it is not cooling properly.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•OBD-II scanner
•Manifold gauge set
•Refrigerant canister (R-134a)
•Socket set
•Torque wrench
•AC compressor removal tool

Parts Required

•AC compressor (if faulty)
•O-rings for refrigerant lines
•Refrigerant oil (specific to compressor)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Scan for error codes using an OBD-II scanner to check for any AC system-related faults.
2
Inspect the AC refrigerant level using a manifold gauge set to determine if it is low or empty.
3
Check the AC compressor for any signs of damage or wear, including electrical connections and the clutch operation.
4
Inspect the cabin air filter for clogs that may restrict airflow.
5
Verify the operation of the AC relay and fuses related to the AC system.
6
Test the temperature of the air coming from the vents with a thermometer to confirm it is not cooling properly.

Solution

1. Preparation

Gather necessary tools and parts.
Disconnect the negative battery cable to prevent electrical shorts.
Ensure the vehicle is parked on a level surface and the engine is cool.

2. Recharge Refrigerant

Tools Required: Manifold gauge set, refrigerant canister (R-134a), AC refrigerant scale.
Connect the low-pressure side of the manifold gauge to the low-pressure service port.
Start the engine and set the AC to maximum cool and high fan.
Check the pressure on the low side; if under 30 PSI, proceed to add refrigerant.
Slowly add refrigerant while monitoring the low side pressure until it reaches the recommended level (typically 30-40 PSI).
Disconnect the manifold gauge and replace the service port cap.

3. Replace AC Compressor (if necessary)

Tools Required: Socket set, torque wrench, AC compressor removal tool, new AC compressor, O-rings, and refrigerant oil.
Remove the drive belt by loosening the tensioner pulley.
Disconnect the electrical connector and refrigerant lines from the AC compressor.
Remove the mounting bolts and take out the old AC compressor.
Install the new compressor by reversing the removal steps; ensure to replace O-rings and fill the compressor with the recommended amount of refrigerant oil.
Reinstall the drive belt and reconnect the electrical connections.

4. Check System Operation

Start the engine and turn on the AC to check for proper function.
Listen for the compressor engaging and monitor the air temperature from the vents.