how to replace tie rod ends on Honda Accord 9th Generation (2013-2017)

Honda Accord Eleventh Generation (2023-present)

Error Codes

2-4 hours

Time

medium

Difficulty

medium

Severity

3 min read

576 words

Problem Statement

Step-by-step guide on how to replace tie rod ends on Honda Accord 9th Generation (2013-2017). Learn symptoms, diagnostic steps, and tools required.

Affected Component

Steering

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Always ensure the vehicle is on a level surface and securely supported by jack stands before working underneath.
•Always disconnect the battery before working on electrical systems.
•Ensure the engine is off and cool before starting repairs.

Symptoms

•Steering wheel feels loose or has excessive play
•Uneven tire wear, particularly on the inner or outer edges
•Clunking or popping noises when turning
•Vehicle pulls to one side while driving
•Vibration in the steering wheel

Diagnostic Steps

1
Inspect the tie rod ends visually for signs of wear or damage.
2
Check for play in the tie rod ends by grasping the tie rod and moving it back and forth.
3
Use a ball joint separator tool to test for movement in the tie rod ends while the vehicle is raised.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Jack
•Jack stands
•Wheel chocks
•Lug wrench
•Socket set
•Torque wrench
•Tie rod end puller
•Grease gun

Parts Required

•New tie rod ends (left and right if necessary)
•Replacement retaining nuts (if required)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Solution

1. Preparation

Tools Required: Jack, jack stands, wheel chocks, lug wrench, socket set, torque wrench, tie rod end puller, grease gun.
Safety Warnings: Always ensure the vehicle is on a level surface and securely supported by jack stands before working underneath.

2. Raise the Vehicle

Use a jack to lift the front of the vehicle.
Securely place jack stands under the vehicle for safety.
Remove the front wheels using a lug wrench.

3. Remove Old Tie Rod Ends

Locate the tie rod ends connected to the steering knuckle.
Use a tie rod end puller to separate the tie rod end from the steering knuckle by applying pressure until it pops off.
Remove the retaining nut from the tie rod end using the appropriate socket.
Unscrew the tie rod end from the inner tie rod by turning it counterclockwise; count the number of turns to aid in proper installation of the new part.

4. Install New Tie Rod Ends

Apply a small amount of grease to the threads of the new tie rod end.
Screw the new tie rod end onto the inner tie rod, matching the number of turns counted during removal to maintain alignment.
Tighten the retaining nut securely using a torque wrench to the manufacturer’s specifications (usually around 30-40 lb-ft).
Reattach the tie rod end to the steering knuckle and secure it with the retaining nut, again using the torque wrench.

5. Reassemble Vehicle

Reinstall the front wheels and hand-tighten the lug nuts.
Lower the vehicle off the jack stands and remove the jack.
Torque the lug nuts to the manufacturer’s specification (usually around 80-100 lb-ft).

6. Final Check

Ensure all components are securely tightened.
Recheck the steering feel and check for any unusual noises.