how to fix oil consumption issues on my Honda Accord 9th Generation (2013-2017)

Honda Accord Eleventh Generation (2023-present)

Error Codes

2-4 hours

Time

medium

Difficulty

high

Severity

3 min read

570 words

⚠️ Safety Warning

This issue requires immediate attention. If you are not experienced with automotive repairs, consult a professional mechanic. Working on critical systems can be dangerous.

Problem Statement

Learn how to diagnose and fix excessive oil consumption in Honda Accord 9th Generation (2013-2017). Step-by-step guide with symptoms and solutions.

Affected Component

Engine

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Disconnect the battery before working on electrical systems.
•Allow the engine to cool before opening the oil drain plug.

Symptoms

•Engine oil level drops significantly between oil changes
•Blue smoke from the exhaust during acceleration
•Unusual engine noise due to low oil levels
•Check engine light illuminated
•Increased frequency of oil top-ups

Diagnostic Steps

1
Check the engine oil level and condition using the dipstick.
2
Inspect for visible oil leaks around the engine and under the vehicle.
3
Perform a compression test to check for worn piston rings or cylinder walls.
4
Conduct a leak-down test to identify potential leaks in the combustion chamber.
5
Inspect the PCV (Positive Crankcase Ventilation) system for blockages or malfunctions.
6
Scan for error codes using an OBD-II scanner to identify related issues.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Socket set
•Pliers
•Compression tester
•Leak-down tester
•Oil filter wrench
•Oil drain pan

Parts Required

•New PCV valve
•High mileage engine oil
•New oil filter

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Check the engine oil level and condition using the dipstick.
2
Inspect for visible oil leaks around the engine and under the vehicle.
3
Perform a compression test to check for worn piston rings or cylinder walls.
4
Conduct a leak-down test to identify potential leaks in the combustion chamber.
5
Inspect the PCV (Positive Crankcase Ventilation) system for blockages or malfunctions.
6
Scan for error codes using an OBD-II scanner to identify related issues.

Solution

1. Preparation

Gather necessary tools and parts.
Ensure the vehicle is parked on a level surface and the engine is cool.
Disconnect the battery to ensure safety during repairs.

2. Inspect and Replace PCV Valve

Tools Required: Socket set, pliers
Steps:
1. Locate the PCV valve on the engine (typically found on the valve cover).
2. Remove the PCV valve by twisting it counterclockwise and gently pulling it out.
3. Inspect the old PCV valve for blockages or damage.
4. Install the new PCV valve by pushing it in and twisting it clockwise until it locks in place.

3. Address Engine Wear

Tools Required: Compression tester, leak-down tester
Steps:
1. Perform a compression test on all cylinders to check for low compression.
2. If low compression is detected, perform a leak-down test to determine if the issue is due to worn piston rings or valve seals.
3. If necessary, replace piston rings or valve seals. This will involve removing the cylinder head and possibly the engine block, requiring more advanced mechanical skills.

4. Oil Change with High Mileage Oil

Tools Required: Oil filter wrench, socket set, oil drain pan
Steps:
1. Drain the old engine oil by removing the oil drain plug and allowing it to fully drain into an oil pan.
2. Replace the oil filter using the oil filter wrench.
3. Reinstall the drain plug and torque it to the manufacturer’s specification (usually around 20-25 ft-lbs).
4. Fill the engine with high mileage oil that includes additives to help reduce oil consumption.