how to fix my Honda Accord 9th Generation (2013-2017) rear brakes that squeak

Honda Accord Eleventh Generation (2023-present)

Error Codes

2-4 hours

Time

medium

Difficulty

medium

Severity

4 min read

620 words

Problem Statement

Learn how to diagnose and fix squeaking rear brakes on Honda Accord 9th Generation (2013-2017). Step-by-step guide with tools and parts required.

Affected Component

Brakes

Estimated Time

2-4 hours

⚠️ Safety Warnings

Important safety information - read before proceeding

•Always disconnect the battery before working on electrical components.
•Allow the vehicle to cool before handling brake components to avoid burns.

Symptoms

•Squeaking noise when brakes are applied
•Increased braking distance
•Brake pedal feels spongy or soft
•Vibrations or pulsations felt through the brake pedal
•Accumulation of brake dust on the wheels

Diagnostic Steps

1
Inspect the rear brake pads for wear using a visual inspection.
2
Check the brake rotors for grooves, scoring, or warping.
3
Verify the brake caliper operation by inspecting for proper movement and any signs of sticking.
4
Assess the brake fluid level and condition in the master cylinder.
5
Examine the brake components for signs of moisture or corrosion.

Solution

💡 Expert Tip

For complex repairs like this, consider taking photos at each step. This helps if you need to reverse a step or consult with a mechanic. Also, keep all removed parts organized - you may need to reference them during reassembly.

Verification

After completing the repair, verify that the issue has been resolved:

✓Test the affected component to ensure it functions correctly
✓Check for any error codes or warning lights
✓Monitor the vehicle for a few days to ensure the issue does not recur

Prevention Tips

To prevent this issue from occurring again:

•Follow the manufacturer's recommended maintenance schedule
•Address warning signs early before they develop into major issues
•Use quality parts and fluids recommended for your vehicle
•Keep detailed records of all repairs and maintenance

Tools & Equipment Required

•Jack and jack stands
•Tire iron or lug wrench
•Socket set
•Brake cleaner
•Torque wrench
•C-clamp or brake caliper tool
•Lubricant (high-temperature brake grease)
•Brake pads (if replacement is needed)
•Brake rotors (if replacement is needed)

Parts Required

•Rear brake pads
•Rear brake rotors (if necessary)

Related Faults

Share this solution

Comments

No comments yet

Be the first to share your thoughts

Back to Generation

Diagnostic Steps

1
Inspect the rear brake pads for wear using a visual inspection.
2
Check the brake rotors for grooves, scoring, or warping.
3
Verify the brake caliper operation by inspecting for proper movement and any signs of sticking.
4
Assess the brake fluid level and condition in the master cylinder.
5
Examine the brake components for signs of moisture or corrosion.

Solution

1. Preparation

Gather necessary tools and parts.
Ensure the vehicle is parked on a flat surface and the engine is off.
Wear safety glasses and gloves for protection.

Tools Required:

Jack and jack stands
Tire iron or lug wrench
Socket set
Brake cleaner
Torque wrench
C-clamp or brake caliper tool
Lubricant (high-temperature brake grease)
Brake pads (if replacement is needed)
Brake rotors (if replacement is needed)

2. Remove the Wheel

Loosen the lug nuts slightly while the vehicle is on the ground.
Use the jack to lift the rear of the car and secure with jack stands.
Remove the lug nuts completely and take off the wheel to access the brake components.

3. Inspect and Replace Brake Pads

Locate the brake caliper and remove the caliper bolts using the socket set.
Carefully slide the caliper off the brake rotor and suspend it using a wire or bungee cord to avoid straining the brake line.
Remove the old brake pads from the caliper bracket.
If the pads are worn below specifications (typically 3mm or less), replace them with new pads.
Apply a thin layer of brake grease to the backing of the new pads to prevent squeaking.

4. Inspect and Replace Brake Rotors (if necessary)

Check the brake rotor surface for any grooves or damage.
If the rotor is below the minimum thickness or excessively worn, remove the caliper bracket and rotor by unscrewing the retaining screws.
Install the new rotor by reversing the removal process, ensuring it is securely fastened.

5. Reassemble Components

Reinstall the caliper over the new pads and rotor.
Tighten caliper bolts to the manufacturer’s specifications (typically 20-25 ft-lbs).
Reinstall the wheel and torque the lug nuts to the specified value (usually around 80-100 ft-lbs).

6. Final Steps

Pump the brake pedal a few times to seat the brake pads against the rotor.
Inspect the brake fluid level, adding fluid if necessary.
Lower the vehicle from the jack stands.